8
GB
9
GB
Precautions (Continued)
•
For 1-temperature models only, place the humidity cartridge (located in
your cabinet’s “accessories” bag) in the base of the cabinet, under the grid,
in the tray provided (see diagram below). When using for the first time,
immerse the entire cartridge in water for a few minutes to saturate it then
drain it thoroughly.
•
Install the stop (which is located in the accessories bag) at the back of the
cabinet (see diagram).
•
This allows a space of 7 cm
to be maintained between
the wall and the rear of the
cabinet. This spa
ce allows your cabinet’s
power consumption to be
optimised.
•
Place the 2 caps in the 2
holes at the top of the
cabinet.
•
Do not push the caps all the
way in, in order to allow the
rear stop to be installed.
•
Slide the rear stop between
the caps and the wall of the
cabinet, then push the 2
caps all the way in.
Installation
Place your cabinet in the desired location.
It must:
•
be open to the outside and well ventilated (not in an enclosed cupboard,
for example),
•
not be too damp (utility room, laundry room, bathroom...),
•
have a flat, stable floor,
•
be supplied with power (standard outlet, 16 A, earthed with 30mA*
circuit breaker). (* not applicable to some countries).
When moving your cabinet, ne
ver tilt it more than
45°, and always on its side (on the opposite
side of
the flexible lead).
•
Place your cabinet in the desired location.
•
Fit the charcoal filter (located in the “accessories” bag) by inserting it into
the breather hole located on the top left-hand side of the inside of your
cabinet (except 6170D model).
•
Take the lead and plug it into the connector, located at the back of the
cabinet, on the bottom left-hand side.
•
Wait 48hrs before plugging in
your cabinet
•
When using your cabinet for the
first time, the charcoal filter
alarm will display. Reset the filter
meter to 365 (see chapter 6, §
VII).
Fitting the handle
1. Full Glass door
•
Unscrew the three screws placed on the side of the door, using the Allen
wrench, which you will find in the handle's box.
Fig.1
Fig.2
Fig.3
Handle
Seal
Front
Door frame
Fig.1
Fig.2
Fig.3
Figure 1
Figure 2
Figure 3
View from above
•
Position the handle on the specially designed groove on the door frame
(figure 2).
•
Insert the handle all the way into the groove using a forward movement
(figure 2).
•
Screw the three screws back on (figure 3).
•
Take care not to catch the seal when screwing.
Note: adjustment of the handle is possible thanks to the oblong holes.
2. Glass door with black frame and plain door
The handle can be found in its protective bag. It is attached to the rack at the
bottom of your cabinet.
•
Move the seal away from the handle position.
•
Screw the 2 screws using the Allen key (3 mm) provided in the bag of
accessories.
•
Reposition the seal ensuring that it is correctly clipped in place.
Installing two cabinets side by side
N.B.: If you are placing two cabinets side by side, ensure that you leave a
gap of at least 1 cm between each cabinet.
4 - i
nstAlling
youR
Wine
CABinet
I. Door reversibility
(Full Glass only)
x3
x4
x3
C
E
x3
D
B
G
F
H
J
A
x2
1
2
4
3
This allows you to change the direction in which the door opens. Follow
the instructions below (example for changing a right-hand door into a
left-hand door):
5
Unscrew the door pin.
6
Carefully remove the cap using a thin blade and assemble the pin in its
place. Reposition the cap on the opposite side
9
Turn the door through 180°.
Warning:
the door is very heavy. Take any necessary
precautions to ensure that you do not injure yourself or drop it.
10
Put the door back on its pin.
12
11
13
1
Unscrew the three screws using a "T25" Torx wrench.
2
Remove the upper hinge.
3
Carefully remove the caps using a thin blade.
4
Remove the cabinet door by opening it slightly, then lifting it upwards.
11
Put in place the upper hinge.
12
Screw the hinge so that the door is completely parallel to the cabinet.
Check that the door seal adheres well to the cabinet (by closing the door),
to ensure that it is completely air-tight.
13
Put in place the caps.
7
Unscrew the two screws and the door catch.
Unscrew the two screws on the opposite side and remove the two
washers.
A
Upper hinge
B
Caps
C
Caps
D
Torx screw
E
Hex screw
F
Door catch
G
Lower hinge
H
Door pin
J
Door pin cap
4
- i
nstAlling
youR
Wine
CABinet
7
8
8
Mount the door catch on the desired opening side, using screws.
Replace the washers, then the screws, on the side opposite the door catch.
