PRECAUTIONARY MEASURES
OPERATING INSTRUCTIONS
Replacing the Filters
Changing & Cleaning the
Pre-Motor Filter
Your vacuum is equipped with a filtration
system to reduce dust and pollen in your
home as you clean. The pre-motor filter
is located inside the vacuum cleaner
body behind the dust bag. Check when
changing the dust bag and replace when
dirty.
This is a rinse-able filter but should be
replaced every three (3) to six (6)
months, depending on usage. Never
operate the vacuum without
ALL
the
filters in place
1. Push the Power On/Off button to the
"Off" position and disconnect the
power cord from the wall outlet.
2. To remove, open the dust bag
compartment cover and remove the
pre-motor filter out of the vacuum.
3. Rinse in lukewarm water and let it air
dry completely for 24 hours. Do not
use a washing machine to rinse the
filter. Do not use a hair dryer to dry it.
Air dry only
. When the pre-motor
filter is completely dry, insert the filter
into the vacuum. (Fig. 11)
Warning:
To reduce the risk of electric
shock, the power cord must be
disconnected before changing the bag or
performing maintenance/ troubleshooting.
2. The post motor filter is located at the
rear of the unit.
3. Push down on the tab of the post
motor filter assembly and pull the
assembly out. (Fig. 12)
4. Remove the post-motor from the
filter assembly. (Fig. 13)
5. Rinse in lukewarm water and let it air
dry completely for 24 hours. Do not
use a washing machine to rinse the
filter. Do not use a hair dryer to dry it.
Air dry only
. When the post-motor
filter is completely dry, insert it in the
filter into the vacuum.
Important
: This unit is equipped with a
motor protective thermostat. If for some
reason the vacuum cleaner should
overheat, the thermostat will
automatically turn the unit off. Should
this occur:
•
Push the On/Off button once.
•
Disconnect the plug from the power
source.
•
Check the source of overheating
problem. (i.e. clogged hose or
filter)
•
If clogged hose or filter is found,
unclog the hose and replace the
filters.
•
Wait at least 45 minutes before
attempting to reuse the vacuum.
•
After unit has cooled down for 45
minutes, plug in the cleaner and
push the On/Off button. The vacuum
should start again.
•
If the vacuum still does not start,
contact customer service at
1 (800) 798-7398.
Motor Thermostat
Fig. 11
Fig. 12
Fig. 13
Changing & Cleaning the Post
Motor Filter
The post motor filter should be replaced
every three (3) to six (6) months
depending on usage. Never operate the
vacuum without
ALL
the filters in place.
1. Push the Power On/Off button to the
"Off" position and disconnect the
power cord from the wall outlet.
Important
:
If the suction opening of the unit, the hose or the extension tubes
are
BLOCKED
, switch off the vacuum cleaner and remove the blocking
substance before you start the unit again.
4.
When pulling out the power plug
from the wall outlet, pull the plug
not the power cord.
1.
Do not operate the vacuum
cleaner too close to heaters or
radiators.
5.
Do not pick up anything that is
burning or smoking such as
cigarettes, matches or hot ashes.
2.
Before inserting the power plug
into the wall outlet, make sure that
your hands are dry.
3.
Before you start vacuuming,
make sure to remove large or
sharp objects that might
damage the vacuum.
6.
Do not use without all filters and
dust bag in place.
Note:
This vacuum cleaner is equipped
with a plug and power cord that retract
automatically. If the cord or plug gets
damaged, it must be replaced by a
qualified technician.
Warning:
Hold the plug when
rewinding the cord. Do not allow
the cord to whip when rewinding.
6
3
Содержание CV520HB
Страница 2: ......
