background image

THE EUREKA

®

 COMMERCIAL

LIMITED WARRANTY

WHAT THIS WARRANTY COVERS

    Your EUREKA commercial cleaner is warranted to be free
from all defects in material and workmanship in normal use FOR
A PERIOD OF ONE YEAR. The warranty is granted only to the
original purchaser of the cleaner. The warranty is subject to the
following provisions.

WHAT THIS WARRANTY DOES NOT COVER

Parts of the cleaner that require replacement under normal

use, such as bumpers, bags, bristle strips, belts, light bulbs,
hoses, fans, and impellers.

Damages or malfunctions caused by negligence, abuse, or

use not in accordance with the Owner’s Guide.

Defects or damages caused by unauthorized service or the

use of other than Genuine Eureka parts.

WHAT THE EUREKA COMPANY WILL DO

    

The Eureka Company will, at its option, repair or replace a

defective cleaner or cleaner part that is covered by this warranty.
As a matter of warranty policy, the Eureka Company will not
refund the consumer’s purchase price.

WARRANTY REGISTRATION

        Please fill out and return the warranty registration card
accompanying your cleaner.

–continued on reverse side–

15

Содержание C2132B - Home Care Commercial Upright Vacuum

















Отзывы: