Antiscalnt Cartridge is
recommended to be installed
if the TDS is above 1000 ppm or
hardness above 300 ppm
PURIFICATION PROCESS OF AQUAGUARD®
BLAZE RO
Copper has antimicrobial, antioxidant, and
anti-inflammatory properties that help to support
healthy metabolism. It also helps to provide the
body with energy and is much needed for growth
and development. The activated carbon removes
organic components and polishes the water,
giving it a sparkling look, making it pure and
great to taste.
The Multi-Stage Purification Process of Aquaguard
®
Blaze Hot & Ambient
i-Filter™
Multi-layered Polypropylene
Roving Wound Cartridge
Removes fine suspended particles such as dust,
dirt mud and sand from wate
Chemi-Block
(with built-in
Particle Trap Filter)
Dust-free Bacteriostatic
Activated Carbon block
filter cartridge with built-in
Particle Trap Filter
Adsorbs colour, odour, excess chlorine & organic
impurities from the incoming water. It removes
very fine turbidity from the water. Its unique Particle
Trap Filter entraps any released micro particles.
Mineral
Guard™
*+
Micro Controller-based
Electronic Impulse
Producer
Prevents the deposition/scaling of dissolved salts
on the surface of the membrane & ensures the
availability of Calcium and Magnesium in your
drinking water.
Membrane
Life
Enhancer
Special Anti-scalant
Media
Prevents scaling of dissolved salts on the surface
of the membrane, thereby, enhancing the
membrane life and performance.
Reverse
Osmosis
Membrane
Thin Film Composite
(TFC) Reverse Osmosis
Membrane
Reduces TDS, hardness, pesticides and heavy
metals like arsenic, lead and mercury. Eliminates
micro-organisms like bacteria, viruses, protozoa
and cysts.
Active
Copper™
Cartridge
+
^^
A patented bacteriostatic
taste enhancer with
Active Copper™
Technology
LED INDICATION CHART FOR AQUAGUARD
®
BLAZE RO
#
CONDITION
LED INDICATION
STATUS
1
Power ON Time
Red, Blue and Green LED will blink one after
other for 1 sec, then Green LED will be solid for
5 seconds.
2
Tank Filling Mode
Blue LED will blink @0.5 secs rate.
3
Tank Full Condition
Blue LED will be solid.
4
SV/Pump Fault(short)
Red LED will blink at 0.5 secs rate.
5
Dry Run Sensor Error
Purple LED will be solid.
6
Electronic
Authentication Fault
Red LED will blink at 0.25 secs rate.
7
Filter Life Warning
While LED blinks slowly.
8
Filter life Completed
(Unit seizes)
White LED blinks fast.
HERE'S HOW YOUR AQUAGUARD®
BLAZE RO WORKS
AQUAGUARD BLAZE RO + HOT & AMBIENT
(WATER FLOW DIAGRAM)
NOTE: THIS IS A SCHEMATIC ILLUSTRATION OF THE PRODUCT TO GIVE A VISUAL SCHEME OF WORKING OF PRODUCTS.
THIS IS NOT AN ACTUAL ENGINEERING DRAWING OF THE PRODUCT
RO MEMBRANE
DRAIN
DIVERTER VALVE PL 6
FLOW RESTRICTOR
MINERAL GUARD
RAW WATER
INLET
REJECT
SOLENOID VALVE
CHEMI-BLOCK
(WITH BUILT-IN PARTICLE TRAP FILTER)
DRY RUN
SENSOR
ZERO PRESSURE
PUMP
HEATING
COIL
WATER
HOT
HOT WATER TANK DRAIN
STEAM
VENT
AMBIENT WATER
HOT WATER TAP
AMBIENT WATER TAP
LEVEL SENSOR
I-
FI
L
TE
R
ACTIVE COPPER
ANTISCALNT CARTRIDGE
TIPS FOR SAFETY AND MAINTENANCE OF YOUR AQUAGUARD
®
BLAZE
TECHNICAL SPECIFICATIONS* BLAZE RO
HOW TO DISPENSE WATER FROM
AQUAGUARD
®
BLAZE
AG BLAZE RO+HOT & AMBIENT
Model
2
Dimension (W X D X H)
330 mm X 440 mm X 490 mm
Net Weight
13 KG (Approx.)
3
Purification Technology
RO
3.9 litres (Ambient water tank - 3.1 litres & Hot
water tank - 0.8 litres)
4
Tank Capacity
I–Filter , Mineral Guard, Chemi–Block, Reverse Osmosis
Cartridge, Active Copper
5
Standard Filtration
supplied
1
1
Power Rating
540 Watts (Heater- 500 Watts)
1
Input Iron (Max.)
0.3 mg/L
2
Total Dissolved Solids
(TDS)
Up to 2,000 mg/L
++
5
Water Temperature
10°C to 40°C
6
Total Hardness (Max.)
600 mg/L
7
Chlorine Content
(Max.)
0.2 mg/L
3
Input Water Turbidity
(Max.)
5 NTU
4
Input Water Pressure
(Max.)
Up to 0.3 to 3 kg/cm
2
1
3
Operating Voltage Range
150 VAC to 250 VAC, 50 Hz
Power Supply
Input 230 VAC (Internal AC – DC Adaptor – O/P 24VDC,
2.5 Amps)
2
ELECTRICAL SPECIFICATIONS
RECOMMENDED INPUT WATER PARAMETERS
PRODUCT SPECIFICATION
*Technical Specifications are subject to change without prior notice.
Note: The performance data presented in the table is applicable under standard laboratory conditions
#
.
Actual performance may vary depending on the input water quality, water pressure and condition of filters.
Input water quality/pressure/TDS are important determinants of recovery rate and rejection.
Warranty void if product not installed as per recommendations.
++
If the input water TDS is more than 1,000 ppm (mg/L) or input water hardness is more than 300 ppm (mg/L),
use of a Membrane life enhancer is recommended. This accessory is available at an extra cost.
2
**If the input water pressure is more than 3.0 kg/cm , installation of a PRV (Pressure Reducing Valve) is mandatory.
#
Standard Test Conditions
:
Feed Water Quality: TDS Max: 1,000 mg/L with NaCl.
Pressure: 1 kg/cm
2
, Turbidity: 1 NTU (Max.), Temperature: 25°C, Chlorine: below 0.2 mg/L, Iron: below 0.3 mg/L
Life: 6,000 Liters. Pressure on membrane: 75 psi & Product recovery @ 25%
To Dispense Ambient Water:
• Press the ambient tap towards the product and the purified water at ambient temperature will flow
through the tap. Release the tap, the water flow will stop.
• To get the ambient water continuously, lift up the tap lever and water will start flowing continuously
as long as the lever is lifted and water is available in the purified water tank. To stop the flow, pull
down the tap lever.
To Dispense Ambient Water:
• To get hot water, the water has to be heated by switching ON the heater switch provided on the left
panel of the product.
• After switching ON the heater switch, it will take about 6 to 8 minutes to reach a water temperature
of 85°C (based on the input water temperature and ambient temperature).
• The hot water will be dispensed through the hot water tap located in the left side of the product in
red colour.
• To dispense hot water, push the child lock button on the tap (projecting on the hot tap) and then push
the lever of hot tap towards product. Release the tap, the water flow will stop.
• To get the hot water continuously, lift up the tap lever and then push the child lock button ON the tap
water will start flowing continuously as long as the lever is lifted and water is available in the purified
water tank. To stop the flow, pull down the tap lever.
Note: The temperature of water flow from hot tap may not be exactly 85°C and it depends on the
duration of the heater switch kept ON and the amount of water drawn. The heating capacity of the
product is 5 litres per hour.
• Read attentively and understand the purifier and its functions, before use.
• Installation and service has to be conducted by authorised persons from Eureka Forbes Limited only.
• Install the purifier at a location with more ventilation.
• Ensure that the purifier is installed in a dry place. Do not expose to direct sunlight or heat sources.
• Ensure that there is a minimum gap of 5cm from the wall, to the rear side of the product, for proper
cooling performance.
• Connect the purifier to 230V AC power socket, duly grounded. Use 500VA voltage stabilizers in
case the voltage fluctuates.
• Turn ON the heater switch located at the right side of the machine to get hot water. It takes some time
for water to get heated after the heater switch is turned ON.
• During installation for first time usage, please do not switch on the heater switch unless water is filled
completely in the storage tank.
***Not a part of the product, Membrane life enhancer is recommended if the input water TDS is more than
1,000 ppm (mg/L) or input water hardness is more than 300 ppm (mg/L). Available at extra cost.
• Discard about 10 litres of water after the installation or after replacing the filter cartridges.
• Do not remove or insert the plug with wet hands.
• Replace the filters when the end of life indicator is displayed by your purifier.
• Ensure that the filter cartridges and spares used during service/replacement, are genuine and from
Eureka Forbes only.
• Always switch off and disconnect the power plug before maintenance or cleaning.
• In case of any damage or incorrect functioning, immediately contact an authorised service centre of
Eureka Forbes Limited. Do not try to repair on your own.
