3
User Information
EUCHNER GmbH + Co. KG Kohlhammerstraße 16 DE-70771 Leinfelden-Echterdingen Tel. +49/711/75 97-0 Fax +49/711/75 33 16 www.euchner.de [email protected]
Emergency Stop Safety Relay ESM-BA2..
V1.1.0
Maintenance
The device must be checked once per month for proper
function and for signs of tampering and bypassing of the
safety function.
Techn. Data
Operating voltage
ESM-BA201
ESM-BA202
ESM-BA203
AC/DC 24V
AC 115V
AC 230V
Rated supply frequency
50-60Hz
Permissible deviation
+ / - 10%
Power consumption
DC 24V
AC 230V
approx. 1.5W
approx. 3.7 VA
Control voltage at S11
DC 24 V
Control current S11...S14
approx. 40 mA
Safety contacts
2 NO contacts
Max. switching voltage
AC 250 V
Safety contact breaking capacity (13-14, 23-24 *)
AC:
250 V, 1500 VA, 6 A for ohmic load
(6 switching cycles/ min)
250 V, 3 A for AC-15
DC: 24 V, 144 W, 6 A for ohmic load
(6 switching cycles/ min)
24 V, 3 A for DC-13
Minimum contact load
24V, 20 mA
Contact fuses
10A gG
Line cross section
0.14 -2.5 mm
2
Max. length of control line
1000 m with 0.75 mm
2
Contact material
AgSnO
2
Contact service life
mech. approx. 1 x 10
7
Test voltage
2.5 kV (control voltage/contacts)
Rated impulse withstand voltage, leakage path/air gap
4 kV (DIN VDE 0110-1)
Rated insulation voltage
250 V
Degree of protection
IP20
Temperature range
DC 24 V:
-15°C to +60°C *)
AC 230V/115V/24V:
-15°C to +40°C
Degree of contamination
2
(DIN VDE 0110-1)
Overvoltage category
3
(DIN VDE 0110-1)
Weight
approx. 230 g
Mounting
DIN rail according to EN 60715 TH35
Note:
Additional data can be requested from the manufacturer for
applications that deviate from these conditions.
Safety
Characteristics
According to
EN ISO 13849-1
The device is certified according to EN ISO 13849-1 up to a
Performance Level of PL e.
Device cannot be switched on again after an emergency
stop:
•
Check whether the emergency stop circuit was closed
again.
•
Was the start button opened before closing of the
emergency stop circuit (with manual start)?
•
Is the feedback loop closed?
If the fault still exists, perform the steps listed under
“Commissioning Procedure”.
If these steps do not remedy the fault either, return the
device to the manufacturer for examination.
Opening the device is impermissible and will void the
warranty.
Device does not switch on:
•
Check the wiring by comparing it to the wiring diagrams.
•
Check the safety switch used for correct function and
adjustment.
•
Check whether the emergency stop circuit is closed.
•
Check whether the start button (with manual start) is
closed.
•
Check the operating voltage at A1 and A2.
•
Is the feedback loop closed
?
What to Do in
Case of a Fault?
The device is otherwise maintenance free, provided that it
was installed properly.
Safety characteristics according to EN ISO 13849-1 for all variants of ESM-BA2
Load (DC-13; 24V)
<= 0,1A
<= 1A
<= 3A
T10d
[years]
20
20
20
Category:
4
4
4
PL
e
e
e
PFHd [1/h]:
1,2E-08
1,2E-08
1,2E-08
nop
[cycle / year]
<= 400.000
<= 100.000
<= 22.500
*) 20% Undervoltage: T
max
: 50 °C
