EUCHNER ECB-A-2K-A1-160397 Скачать руководство пользователя страница 21

Страница: 21 / 30

2533580-02-03/20 (Translation of the original operating instructions)

Operating Instructions

Euchner Control Box ECB-...

9. Setup

9.1. Teaching-in a new CKS key

Teach-in of CKS keys can be repeated any number of times. Observe the teach-in operation in accordance with section

9.1.2. Teach-in operation on the CES evaluation unit for this purpose. Faulty CKS keys can thus be replaced at any time. In

the delivery state, the keys in the evaluation unit have already been taught-in.

9.1.1. LED indicators on the CES evaluation unit

Designation

Color

Meaning

State

green

Status indication (multifunction display using flashing modes)

OUT

yellow

Safety circuit closed

DIA

red

Operating fault or

External fault (fault in the feedback loop) or

Teach-in operation not valid or

Internal device fault or

TST input activated (function test active)

O2
Y1

STATE OUT DIA

+UB

SH1
SH2

H12
H22

H11
H21

DIA

TST

CES - AZ

Safety Unit

RESET

Unicode

Figure 12: Evaluation unit CES-AZ-AES-02B

9.1.2. Teach-in operation on the CES evaluation unit

A new CKS key can be taught-in on the CES evaluation unit if necessary.
During the teach-in operation the safety outputs are open. The system is in the safe state.

Important!

CKS keys must not be removed during the teach-in operation.

If the teach-in operation is interrupted, the CES evaluation unit switches to the safe fault state

(diagnostic LED illuminates) and signals this operating fault with the STATE LED by 3 short flashes

that are repeated every 1 second. The teach-in operation must be repeated.

The number of teach-in operations is unlimited. The CES evaluation unit can be re-configured as

often as required.

CKS key adapters cannot be interchanged without a renewed teach-in operation.

If a CKS key is not taught-in, it is not recognized by the respective CKS key adapter.

Even if only one new CKS key needs to be taught-in, a complete new teach-in operation must be

carried out.

Do not change DIP switches during operation.

Содержание ECB-A-2K-A1-160397































Результаты поиска

Содержание ECB-A-2K-A1-160397

Отзывы:

Похожие инструкции для ECB-A-2K-A1-160397

Бренды по названию

Популярные бренды

EUCHNER ECB-A-2K-A1-160397, Руководство по эксплуатации

Результаты поиска

Содержание ECB-A-2K-A1-160397

Отзывы:

Похожие инструкции для ECB-A-2K-A1-160397

Бренды по названию

Популярные бренды