EUCHNER 097075 Скачать руководство пользователя страница 15

Страница: 15 / 44

2097098-18-10/19 (Translation of the original operating instructions)

Operating instructions

Non-Contact Safety System CES-A-UEA-02B/CES-A-UEA-04B

9. Setup

9.1. LED indicators

Designation

Color

Meaning

STATE

green

Status indication (multifunction display using flashing modes)

OUT

yellow

Safety circuit closed

DIA

red

Operating fault or

External fault (fault in the feedback loop) or

Invalid parameter setting operation or

Internal device fault or

TST input activated (function test active)

9.2. Parameter setting

Before the system forms a functional unit, the parameters are set in the evaluation unit (number of connected read heads,

assignment of the actuators to the read heads, with or without automatic start, with or without feedback loop). During this

process the read heads are activated.
These configuration parameters are saved in the device.
During the parameter setting operation the safety outputs are open. The system is in the safe state.

Important!

The parameter setting operation can differ for read heads that are not described in this document.

Observe the information in the operating instructions for the read head used.

During the parameter setting operation the following conditions must be met:

-There must be no state change, e.g. opening or closing of the safety door or a change in the

signal on the terminals for the start button and the feedback loop.

-The power supply must not be switched off.

If these conditions are not met, the evaluation unit switches to the safe fault state (diagnostics LED

illuminates) and signals this operating fault with the STATE LED by 3 short flashes that are repeat-

ed every second. The parameter setting operation must be repeated.

The number of parameter setting operations is unlimited. The evaluation unit can be re-configured

as often as required.

Do not change DIP switches during operation.

To trigger a parameter setting operation, the user must perform the following actions in the stipulated order:
1. Prepare for parameter setting

-Switch off power supply U

-Fit a jumper between terminals J1 and J2

2. Set required configuration on DIP switches

Switch designation

Switch position left (OFF)

Switch position right (ON)

No read head connected to terminals

H11, H12, SH1

Read head connected to terminals

H11, H12, SH1

No read head connected to terminals

H21, H22, SH2

Read head connected to terminals

H21, H22, SH2

No read head connected to terminals

H31, H32, SH3

Read head connected to terminals

H31, H32, SH3

No read head connected to terminals

H41, H42, SH4

Read head connected to terminals

H41, H42, SH4

Automatic start

(no start button connected)

Manual start

(start button connected)

No feedback loop connected

Feedback loop connected

3. Set required configuration on machine

-Close all doors to be monitored (the actuators must be in the actuating range of the related read head)

-For operating mode

Manual start

: keep start button closed

-For operating mode

with feedback loop

: keep feedback loop closed

Содержание 097075













































Результаты поиска

Содержание 097075

Отзывы:

Похожие инструкции для 097075

Бренды по названию

Популярные бренды

EUCHNER 097075, Руководство по эксплуатации

Результаты поиска

Содержание 097075

Отзывы:

Похожие инструкции для 097075

Бренды по названию

Популярные бренды