ETS Sunvision Elite 48V Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 40

ETS Sunvision Elite 48V Скачать руководство пользователя страница 39

26851-01A

Parts List

This is a list of parts which may be replaced by the
consumer. Care should be taken when replacing
anything related to electrical wiring. We recom-
mend contacting a professional electrician.
When calling for parts, first state your booth model
as P-48SV. Then refer to this list and preceding
illustrations for proper part identification.

Air Dam* (Foam inside cover panel)
Ballast, 160W
Bronze Hinge Bushing*
Capacitor, 75uF
Contactor
Cover Panel
Cover Panel w/ Decal*
Cover Panel w/ Power Cut-outs*
Dome
Fan, 6”
Fan, 16”
Fan Relay
Grill
Handle, Door
Handle, Inside*
Handle, Outside
Hardware Kit*
Hinge Locking Pin*

Lamp Holder w/ Starter Holder
Lamp Holder w/o Starter Holder
Lamps
Manual*
Pedestal
Profile, Edge Cover
Profile, Trim
Remote Connection PCB
Remote Control Bypass Plug*
Schematic Packet*
Silk-screened Profile, English
Silk-screened Profile, French
Speaker (pair)
Starter, K-12
Timer Assembly
Wiring Harness, Keypad to Timer*
Wiring Harness, Remote PCB to Timer*

* Not shown

Record this information for ease of service:

Date of purchase:

Serial number:

«
...
37
38
39
40
»

Содержание Sunvision Elite 48V









































Отзывы:

Нет отзывов