background image

Images are for illustrative purposes.

We reserve the right to make changes.

RDT-064-0722

5

®

NORD

canopy

  

 

|

   

UV 1.0 installation guide

Product safety instructions

Failure to comply with these instructions or incorrect use of this device may cause serious bodily injury. 

The UV cleaning system is designed to treat kitchen exhaust air with UV light and ozone only as described in 

this manual. 

Use of this UV technology reduces odors and reduces fat, mold and bacteria to water vapor and dry minerals. 

ETS NORD AS assumes no liability if the product is not used in accordance with the manufacturer’s instructions 

in this guide. 

The installation of the Control Unit may only be carried out by persons trained and authorized by ETS NORD in 

accordance with international standards and regulations.  

It is forbidden to use replacement lamps or any other spare parts that are not supplied by ETS NORD Customer 

Service. 

Ultraviolet radiation and ozone are harmful to health. Prolonged exposure can cause the following damage:

•  Skin rashes and burns 
•  Eye irritation, retinal burn and loss of vision 
•  Respiratory irritation and breathing problems

When removing grease filters from a UV-canopy, ensure that the UV system is powered off at the main 

electrical closet or safety breaker.  

When installing servicing or servicing the lamps, always wear goggles and protective gloves to protect against 

quartz fragments in case of UV-C lamp breakage.

Check your product

Make sure that all components are received, matching both the order and delivery confirmation letters. Incorrect 

delivery and transport damage must be immediately reported to both the cargo carrier and ETS NORD Customer 

Service.  

The time for filing a complaint or shipment discrepancy is 5 days after delivery. ETS NORD is not responsible 

for defects that have occurred after goods have been handed over to the buyer. 

If goods purchased from ETS NORD have defects for which ETS NORD is responsible, ETS NORD will repair 

or replace the defective goods. If the goods cannot be repaired or replaced, ETS NORD will refund to the buyer 

all fees for such items resulting from the sales contract. 

If you have any problems, please contact ETS NORD Customer Service! 

Содержание NORDcanopy























Отзывы: