WARNING:
To reduce the risk of fire, electric shock, or injury to persons: Use only insulated staples or plastic ties to secure cords. • Route and secure cords so that they will not be
pinched or damaged when the cabinet is pushed to the wall. • Do not use for recessed installation in ceilings or soffits. • CAUTION: The National Electrical Code (NEC) does not permit
cords to be concealed where damage to insulation may go unnoticed. To prevent fire danger, do not run cord behind walls, ceilings, soffits, or cabinets where it may be inaccessible
for examination. Cords should be visually examined periodically and immediately replaced when any damage is noted. • Maximum number of units to be interconnected: 53508101
(18 in. under cabinet light): maximum 30 units. Maximum distance between connected units is 14.5 in. • To prevent electric shock, match wide blade of the plug to the wide slot and
fully insert into the electrical outlet.
NOTICE:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna, increase the separation between the equipment and the receiver, connect the equipment into an outlet on a circuit different from that to which
the receiver is connected, and consult the dealer or an experienced radio/TV.
• Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. • Not for emergency lighting.
See website for Warranty, Troubleshooting or Care and Cleaning details at www.ETiSSL.com.
Questions, problems, missing parts? Call ETiSSL Customer Service 8 a.m. - 5 p.m., CST, Monday - Friday
1-855-ETI-SSLI (1-855-384-7754) www.ETiSSL.com
LInkIng feature
WARNING: RISK OF ELECTRIC SHOCK. Disconnect power to the under cabinet light before linking
additional under cabinet lights.
Multiple light fixtures can be connected, up to a maximum of 300 total watts.
Only the first light fixture needs to be plugged into an electrical outlet or directly wired.
Provide power to the fixtures only after all linking connections have been made.
Connect each additional fixture using either the linking cable or end-to-end connector. Remove the
end cover and insert either the end to-end connector or linking cable into the receptacle in the end
of each under cabinet light fixture. When using the linking cable, the maximum distance between two
light fixtures is 14.5 in. using the linking cable provided.
Use wire clips to affix the linking cable to the underside of the cabinet, if desired.
I
J
A
A
A
A
BeaM aDjustMent feature
Rotate the tabs on each end of the light fixture to adjust the light angle to the desired position.
NOTE:
A minimum of 60% of the total lumen output is achieved in an adjustable beam angle
of 22.5°.
oPeratIng the fIxture
Use the toggle switch on the fixture to control the light.
If the under cabinet lights are installed on a dimming circuit, use the dimmer switch to adjust the
brightness.
NOTE:
Color of the light warms when dimmed starting at the selected Color Temperature (CCT)
2700K/3000K/4000K/Grow Mode.
Toggle Switch
Model no.
Part no.
Maximum connected units
53508101
GL-18IN-500LM-8-CP3-SV-TD
30
La versión española está en el
sitio web www.ETiSSL.com.
