Package contents
Part Description
Quantity
A
Fixture
1
B
Strain Relief Clamp
1
C
O-Ring
2
D
Wire Clip
2
E
Mounting Screw (long)
2
F
Drywall Anchor
2
G
MagnaMount™
Mounting Plate
1
H
Plug Connector
1
I
14.5 in. Linking Cable
1
J
End-to-End Connector
2
K
Mounting Screw (short)
2
L
V-clip
2
Hardware not shown to actual size.
NOTE
:
Keep your receipt and these instructions for proof of purchase.
WARNING
:
RISK OF ELECTRIC SHOCK. Ensure the electricity to the wires
you are working on is shut off. Either remove the fuse or turn off the circuit
breaker before removing an existing light fixture or installing the new one.
If you are unfamiliar with electrical installations, we recommend you contact
a qualified electrician to do the installation.
NOTE
:
Installing contractor is responsible for selecting a suitable location
that can support the weight of the fixture and determining the method for
mounting the fixture before installing, based on the type of ceiling.
InstaLLatIon
Shut off power at the electrical panel before beginning the installation.
Remove existing fixture and set aside to recycle in accordance with local
requirements.
Installing contractor is responsible for ensuring required CCT is selected
during installation.
NOTICE
:
The factory setting for the correlated color temperature (CCT) is
2700K, which is the warmest white light.
Installing contractor is responsible for determining if the power is
supplied from the plug connector or if the fixture should be directly wired.
Suspension mounted fixtures cannot be directly wired.
NOTE
:
Do not use the linking cable or the plug adapter if directly wiring the
fixture.
If using the plug connector, skip this step.
If directly wiring the fixture:
• Unscrew the 4 screws to remove the back plate.
• Punch out one of the knock out holes on the back
plate.
If installing the MagnaMount™ mounting plate:
• Punch out the matching knock out hole on the
MagnaMount™ mounting plate.
Insert the strain relief clamp into the knock out hole
from the outside in on the back plate.
UsE ANd CARE GUIdE
AdjUsTAblE lEd UNdER CAbINET lIGhT WITh GROW MOdE
Model # 53508101
Part # Gl-18IN-500lM-8-CP3-sV-Td
Certification # 53508101
A
1
2
3
4
5a
surface MountIng
If installing the MagnaMount™ mounting plate for
installation, push a short mounting screw through one of
the screw holes on the MagnaMount™ mounting plate and
then through an O-Ring. Repeat with the remaining short
mounting screw.
If attaching to drywall instead of to the underside of a
cabinet, drill pilot holes and tap in the drywall anchors at
the screw positions.
NOTE
:
Distance between 2 holes is 14.75in.
6a
7a
If using the plug connector or installing without the
MagnaMount™ mounting plate, skip this step.
If directly wiring the fixture and installing the
MagnaMount™ mounting plate, feed the wires
through the MagnaMount™ mounting plate.
If installing the MagnaMount™ Mounting Plate,
screw the MagnaMount™ mounting plate to the
underside of the cabinet or to the drywall and make
sure it is secure.
8a
If using the plug connector, skip this step.
If directly wiring the fixture, feed the wires from
the power supply through the strain relief clamp
in the back plate.
If using the plug connector, skip this step.
If directly wiring the fixture:
NOTE
:
Make sure end cap is tightly in place before making
the electrical connections.
Make the electrical connections:
• Black wire to black wire.
• White wire to white wire.
• Green wire to ground wire.
Use wire connectors (not included) to cover the wire
connections and cover with electrical tape.
Tuck wires inside the fixture.
Reattach the back plate to the fixture.
11a
Knock out Holes
Back Plate
A
B
C
E
G
H
I
J
F
D
K
L
G
K
C
G
Back
Plate
B
Wire Connectors
Wires
Wires
Screw
Back Plate
9a
10a
B
Back Plate
K
C
B
