EtherWAN EX24000 Скачать руководство пользователя страница 92

Страница: 92 / 239

STP/RING PAGE - CONFIGURING RSTP

Global Configuration Page

To navigate to the

STP/Ring Global Configuration

page:

1. Click on the

next to

STP/Ring

2. Click on

Global Configuration

Enabling the RSTP Protocol

RSTP is enabled by Default. If RSTP has been disabled and you wish to enable it (see

Figure 39

1. Click the dropdown box next to

Spanning Tree

Protocol and choose

Enable

2. Click on the dropdown box next to

STP Version

and select

RSTP

3. Click on the

Update Setting

button.

Additional Global Configuration page settings



Bridge Priority

– Bridge Priority is used to set the Root and backup Root Bridge.

For more details see

The Root Bridge & Backup Root Bridge

Default is 32768. Range is 0 to 61440.



Hello Time

– This tells how often a BPDU (Bridge Protocol Data Unit) is sent

(see

Bridge Protocol Data Units

). Default is 2 seconds. Range is 1 to 10 seconds.



Max Age

– Default is 20. Hop count limit for BPDU packets (see

Setting the MAX

Age, Forward Delay and Hello Timer



Forward Delay

Default is 15 sec.

Note: Bridge Protocol Data Units

(BPDUs) are frames that contain information

about the Spanning tree protocol (STP). Switches send BPDUs using a
unique MAC address from its origin port and a multicast address as destination
MAC (01:80:C2:00:00:00). There are three kinds of BPDUs:



Configuration BPDU, used by Spanning Tree Protocol to provide information to

all switches.



TCN (Topology change), tells about changes in the topology.



TCA (Topology change Acknowledgment), confirm the reception of the TCN.

EX24000 Switch Users Guide

Содержание EX24000
















































































































































































































































Результаты поиска

Содержание EX24000

Отзывы:

Похожие инструкции для EX24000

Бренды по названию

Популярные бренды

EtherWAN EX24000, Руководство пользователя

Результаты поиска

Содержание EX24000

Отзывы:

Похожие инструкции для EX24000

Бренды по названию

Популярные бренды