EtherWAN EX24000 Скачать руководство пользователя страница 211

Страница: 211 / 239

Monitoring Registered Multicast Groups

To navigate to the

Multicast Current Table

page:

1. Click on the

next to

Other Protocols

2. Click on

IGMP Snooping

3. Click on the

Multicast Current Table

link at the top of the page.

When the switch is in IGMP Passive

IGMP Querier mode, registered Multicast Groups

can be monitored on each port, as well as the location of the IGMP Querier port (see

Figure

107



All the registered multicast Groups will be listed in the

Group Address

column.



The port where each registered Group ID was received can be found in the

Membership

column in each registered Groups corresponding row.

Note: when an IGMP Querier port is present, all registered multicast group IDs will

show up in the

Membership

column as a checked box for the IGMP Querier port, even if

IGMP Join

was never received for that Group ID on the Querier port.

Figure 107: Current Multicast Groups

211

EX24000 Switch Users Guide

Содержание EX24000
















































































































































































































































Результаты поиска

Содержание EX24000

Отзывы:

Бренды по названию

Популярные бренды

EtherWAN EX24000, Руководство пользователя

Результаты поиска

Содержание EX24000

Отзывы:

Бренды по названию

Популярные бренды