Etesia MBR50 Скачать руководство пользователя страница 22

Страница: 22 / 28

9• BREAKDOWNS AND REMEDIES

ABNORMAL OPERATION

PROBABLE CAUSE

REMEDY

The engine does not start

Fuel tank empty

Fill with petrol

Throttle regulation lever not at choke with cold engine Set throttle regulation lever to choke

Badly connected spark plug cap

Connect the spark plug cap

Fuel pipe blocked

Have the fuel pipe cleaned by a specialist workshop

Air has penetrated the engine because the carburettor

is loose

Tighten the fixing screws

Petrol valve closed

Open petrol valve

The engine does not start ; there is a smell of

petrol

The engine is receiving too much fuel

Put the throttle on MAX do not use the choke

Air filter clogged

Clean the air filter

Engine runs erratically, misses

The engine is running with the choke on

Take throttle regulation lever out of choke position

Ignition cable loose

Allow the engine to cool and carefully connect the

spark plug lead

Air filter clogged

Clean the air filter

Fuel tank cap breather blocked

Replace the fuel tank cap

Fuel pipe blocked

Have the fuel pipe cleaned by a specialist workshop

Carburettor wrongly adjusted

Have the carburettor adjusted by a specialist workshop

Engine misses at high running speeds

Spark plug gap wrongly set

Have the gap set by a specialist workshop

Carburettor wrongly adjusted

Have the carburettor adjusted by a specialist work-

shop

The engine gets too hot

Too little engine oil

Top up with engine oil

Obstructed air cooling system

Have the fan grille and cooling fins cleaned by a spe

cialist workshop

Air filter clogged

Clean the air filter

Carburettor wrongly adjusted

Have the carburettor adjusted by a specialist work-

shop

The engine often stalls on idle speed

Throttle regulation lever not at choke with cold engine Set throttle regulation lever to choke

Spark plug gap wrongly set

Have the gap set by a specialist workshop

Air filter clogged

Clean the air filter

The engine has too little power

Air filter clogged

Clean the air filter

Compression too low

Go to a specialist workshop

The engine does not stop

The engine stop action is out of adjustment

Close the petrol cap and wait for the engine to stop.

Have the engine checked by a specialist workshop

Whistling when the sweeping brush is running

Clutch lever not fully lowered

Push down gear lever for brush drive fully

Incorrect setting for the clutch cable

Correct the setting of the clutch cable

Defective trapezoidal belt

Have the trapezoidal belt replaced by a specialist work-

shop

Noise at brush level

Bristles installed incorrectly

Install bristles correctly

Bristles loose

Check bristles are seated correctly

The brush is not an original

Replace the brush with original Etesia items.

Содержание MBR50





























Результаты поиска

Содержание MBR50

Отзывы:

Похожие инструкции для MBR50

Бренды по названию

Популярные бренды

Etesia MBR50, Оригинальное руководство пользователя

Результаты поиска

Содержание MBR50

Отзывы:

Похожие инструкции для MBR50

Бренды по названию

Популярные бренды