DETECTION AREA
1
2
I
100%
II
75%
III
50%
IV
10%
KEY: ON:
OFF:
DAYLIGHT SENSOR
5
6
I
Disable
II
50 Lux
III
10 Lux
IV
2 Lux
KEY: ON:
OFF:
HOLD TIME
3
4
I
5s
II
90s
III
5min
IV
15min
KEY: ON:
OFF:
READ THIS FIRST:
Check the pack and make sure you have all of the
parts listed on the front of this booklet. If not,
contact the outlet where you bought this product.
This product must be installed by a competent
person in accordance with the current building and
IEE wiring regulations.
As the buyer, installer and/or user of this product it
is your own responsibility to ensure that this fitting
is fit for the purpose for which you have intended
it. Eterna Lighting cannot accept any liability for
loss, damage or premature failure resulting from
inappropriate use.
This product is designed and constructed according
to the principles of the appropriate British Standard
and is intended for normal domestic service.
Switch off the mains before commencing installation
and remove the appropriate circuit fuse or lock off
MCB.
This product is designed for permanent connection
to fixed wiring: this must be a suitable circuit
(protected with the appropriate MCB or fuse).
When making connections ensure that the terminals
are tightened securely and that no strands of wire
protrude. Check that the terminals are tightened
onto the bared conductors and not onto any
insulation.
This product is double insulated.
DO NOT CONNECT
ANY PART TO EARTH.
This product is not intended to be used by children
and persons with sensory, physical and/or mental
impairments that would prevent them from using it
safely.
You are advised at every stage of your installation to
double-check any electrical connections you have
made. After you have completed your installation
there are electrical tests that should be carried out,
these tests are specified in the current IEE wiring and
building regulations.
INTRODUCTION:
This is a microwave sensing device which continuously
scans the operating zone and immediately switches
the light on when it detects movement in that area.
This means that whenever movement is detected
within the range of the sensor the light will switch
on automatically and illuminate the area you have
selected to light. While there is movement within
range of the unit the light will remain on.
A microwave sensor is an active motion detector
emitting high-frequency electro-magnetic waves at
5.8GHz and receiving their echo. The sensor detects
change in the echo pattern within its detection
zone and the light is then triggered. The wave can
pass through doors, glass and thin walls and will
continually monitor the signal within the detection
area.
MICROWAVE SENSOR SPECIFICATIONS:
INSTALLATION:
Isolate mains and lock off.
1) Connect mains and output as per below image,
brown to live, blue to neutral on input and adjust
control accordingly.
2) Restore the power and switch on.
UNDERSTANDING THE CONTROLS:
The sensor is an active motion detector: it emits a
high frequency electromagnetic wave 5.8GHz and
receives its echo. The sensor detects the change
in echo from movement in its detection zone. A
microprocessor then triggers the switch light ON
command. Detection is possible through doors,
panels of glass and thin walls.
DETECTION RANGE:
This determines the effective range of the motion
detector and is set up by DIP switches at the
sensor itself, refer to figure. Note that reducing the
sensitivity will also narrow the detection range.
The following settings
are available:
I - Detection Range 100%
II - Detection Range 75%
III - Detection Range 50%
IV - Detection Range 10%
HOLD TIME:
This determines the time the fitting remains at
100% level on motion detection and is set with DIP
switches at the sensor itself, refer to figure. The walk
test setting is useful when installing the fitting to
establish correct operation and range.
The following settings
are available:
I - Walk test mode 5s
II - 90s
III - 5 minutes
IV - 15 minutes
DAYLIGHT SENSOR:
This setting holds off the 100% light output should
there be sufficient daylight and is set using DIP
switches at the sensor, refer to figure.
The following settings are available:
I - Photocell disabled
II - 50 lux twilight operation
III - 10 lux twilight operation
IV - 2 lux darkness operation only
* In daylight setting the
lamp(s) will always be on
with motion detected
and operate at 100% light
output, even in bright
daylight.
1-2 Detection
Area
Daylight
Sensor
Power
Supply
220-240V
Out Control
Off / On
3-4 Hold
Time
5-6 Daylight
Threshold
Microwave
Sensor
OFF ON
PRODUCT
TYPE
MICROWAVE
MOTION SENSOR
Operating Voltage
220-240VAC 50/60Hz
HF System
5.8GHz CW radar
Transmission Power
<0.2mW
Detection Angle
30-150 Degree
Power Consumption
<0.5W
Detection Range
Max. 10m adjustable
Time Setting
5s-15m
Mounting
Indoors, ceiling and wall
Light Control
2-50lux, disable
Working Temp
-20 to +60 degree
Rated Load
800W (resistive load)
400W (capacitive load)
270W (LED)
RED DIRECTIVE
Eterna Lighting Ltd
Microwave Occupancy Sensor
Full declaration available at www.eterna-lighting.co.uk
