��
����������
����
����
����������
�����
����
General Information, Safety Instructions & Installation:
Installation & Fan Instructions:
READ THIS FIRST:
Check the pack and make sure you have all of
the parts listed on the front of this booklet. If
not, contact the supplier where you bought this
product.
IMPORTANT SAFEGUARDS
When using an electrical appliance, basic safety
precautions should always be observed, including
the following:
• If operating the heater as a freestanding
appliance, ensure the feet are correctly attached
beforehand.
• This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they have
been given supervision or instruction concerning
use of the appliance by a person responsible for
their safety.
• Extreme caution is necessary where children or
persons with reduced physical, sensory or mental
capabilities may come into contact with the heater
when in use.
• The product is for household/office use only.
• In order to avoid overheating do not cover or
obstruct grilles or air intake openings when in use.
• Do not place the heater on carpets with a very
deep pile.
• Always ensure that the heater is placed on a
firm level surface and ensure that the heater is not
positioned close to flammable materials, such as
curtains, drapes etc as this could create a fire hazard.
• The heater must not be located adjacent to or
against an electrical socket.
• Do not run the cord under carpets/rugs.
• Arrange the cord away from high traffic areas
and where it will not become a trip hazard.
• Keep the mains lead away from the heater when
in use.
• Do not operate the heater with a damaged cord/
plug or if the heater malfunctions.
• If the supply cord is damaged, it must be replaced
by a qualified engineer.
• Avoid the use of an extension cord as this may
overheat and cause a risk of fire.
• Do not use the heater in any areas where petrol,
paint or other flammable liquids or flammable
fumes may be present e.g. garages or workshops.
• Do not use this heater in the immediate
surroundings of a bath, shower, swimming pool or
where water is present.
• This heater is hot when in use. To avoid burns
and personal injury, do not let bare skin touch hot
surfaces.
• Never leave the heater unattended whilst it is
in use.
WARNING:
• This product must only be operated in an upright
position.
OPERATION OF THE HEATER:
NOTE:
It is normal for the heater to smell slightly
for a short while when turned on for the first or
after a period of not being used.
ATTACHING THE FEET:
1. Tip heater upside down.
2. Attach feet to each end of the heater using the
screws provided. Affix the feet using 2 screws
diagonally to correspond with the pre cut holes.
Fasten securely.
3. Turn heater correct way up.
WALL MOUNTING THE HEATER:
CAUTION:
The heater must be installed away
from flammable surfaces at least 40cm between
the lower part of the appliance and the floor, 50
cm in front/side and 100cm below any given
surfaces as shown in fig. 1 opposite.
The feet must be removed before mounting the
appliance on the wall.
1. Measure the distance between the two slots
situated at the back of the appliance (see fig.2).
2. Drill two holes at the same distance in the wall
and insert a wall plug in each hole.
3. Place the brackets facing the holes as indicated
on fig.3 (slots upwards) and attach them in this
position with the screws supplied.
4. Before attaching the appliance on the brackets,
attach the two other brackets underneath the
appliance as indicated on fig.4.
5. Attach the appliance on the wall. To do so, hold
it in such way that the slots are facing the brackets;
insert the appliance halfway onto the brackets until
the appliance can go down into the grooves of the
brackets.
6. As soon as the appliance is positioned correctly,
take a pencil and mark a dot in the hole of each
bracket situated underneath the appliance.
7. Then remove the appliance.
8. Drill a hole in the wall as marked and insert a
wall plug in each hole.
9. Attach the appliance back on the wall as
indicated in point 5, insert screws through the
brackets underneath the appliance and tighten.
WALL MOUNTING THE HEATER DIAGRAMS:
INSTRUCTIONS FOR USE / FAN OPERATION:
This heater also incorporates an internal fan, which can be switched on independently of the heating
elements.
This is operated by turning the switch on to the “fan” symbol (opposite).
The fan will only operate with the thermostat in the “on” position and can be
used when the heating elements are “on” to blow warm air into the room.
In warm conditions the fan can be used with the heating elements “off” to
blow cool air into the room.
• Choose a suitable location for the heater, taking into account the safety
instructions above.
• Insert the plug of the heater into a suitable socket.
• Turn the thermostat knob fully in a clockwise direction to the maximum setting.
• Turn on the heating elements by means of the rocker switches on the side panel. When the heating
elements are on the switches will illuminate. For maximum heat output both switches should be on.
Example:
Switch one = 750W
Switch two = 1.25kW
Combined = 2kW
• When the desired room temperature has been reached, the thermostat knob should be turned slowly
anti-clockwise until the thermostat click is heard and the lights on the element switches are seen to go
out. After this the heater will keep the air temperature in the room at the set temperature by switching
on and off automatically.
Fig 1
Fig 2
Fig 3
Fig 4
