ETC Halcyon Gold Скачать руководство пользователя | Manualshive

Страница: 33 / 38

background image

Error Codes

28

Gobo 2

This message displays after the reset of the fixture if any of the following conditions exist:

• the magnetic-indexing circuit malfunctions (optical or magnetic sensor failure)
• the stepper motor is defective or the related IC driver on the main PCB has failed
• Gobo Wheel 2 is not located in the default position after the reset

Gobo Rot 1

This message displays after the reset of the fixture if any of the following conditions exist:

• the magnetic-indexing circuit malfunctions (optical or magnetic sensor failure)
• the stepper motor is defective or the related IC driver on the main PCB has failed
• Gobo Rotating Wheel 1 is not located in the default position after the reset

Iris

This message displays after the reset of the fixture if any of the following conditions exist:

• the magnetic-indexing circuit malfunctions (optical or magnetic sensor failure)
• the stepper motor is defective or the related IC driver on the main PCB has failed
• the Iris is not located in the default position after the reset

Pan

This message displays after the reset of the fixture if any of the following conditions exist:

• the yoke’s magnetic-indexing circuit malfunctions (optical or magnetic sensor failure)
• the stepper motor is defective or the related IC driver on the main PCB has failed
• the Pan movement is not located in the default position after the reset

Prism 1

This message displays after the reset of the fixture if any of the following conditions exist:

• the fixture head magnetic-indexing circuit malfunctions (optical or magnetic sensor

failure)

• the stepper motor is defective or the related IC driver on the main PCB has failed
• Prism wheel 1 is not located in the default position after the reset

Prism 2

This message displays after the reset of the fixture if any of the following conditions exist:

• the fixture head magnetic-indexing circuit malfunctions (optical or magnetic sensor

failure)

• the stepper motor is defective or the related IC driver on the main PCB has failed
• Prism wheel 2 is not located in the default position after the reset

Prism_Rot 1

This message displays after the reset of the fixture if any of the following conditions exist:

• the fixture head magnetic-indexing circuit malfunctions (optical or magnetic sensor

failure)

• the stepper motor is defective or the related IC driver on the main PCB has failed
• Prism rotating wheel 1 is not located in the default position after the reset

«
...
31
32
33
34
35
...
»

Содержание Halcyon Gold







































Отзывы:

Нет отзывов

Похожие инструкции для Halcyon Gold

SACE Tmax XT Series

Бренд: ABB Страницы: 11

Бренд: ABB Страницы: 50

ACS880-01 Series

Бренд: ABB Страницы: 17

Бренд: ABB Страницы: 36

Бренд: Napoleon Страницы: 2

Бренд: Raytheon Страницы: 62

Бренд: Makita Страницы: 8

Бренд: VECTECH Страницы: 5

Бренд: MADRIX Страницы: 12

Бренд: Narcotrend Страницы: 47

Бренд: Danelec Страницы: 67

Бренд: Hacker Страницы: 2

Бренд: J.P. SELECTA Страницы: 8

Бренд: Haemonetics Страницы: 134

Бренд: Hadeco Страницы: 72

Бренд: Teac Страницы: 44

Бренд: Te Pari Страницы: 6

Бренд: Ekinex Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды