background image

ETC Installation Guide

Dual Tech Wall-mount Vacancy Sensor

Prepare for Installation

Echo Dual Tech Wall-mount Vacancy Sensors ship with electronics, a
decorator style wall plate, and a termination kit. The sensor may be installed
into an industry standard back box (provided by others) or surface mounted
back box (sold separately and available from ETC).

Compliance

cULus Listed

CE compliant

For use with ETC Echo Control Systems, powered by an Echo station power
supply.

Environment

Ambient

For indoor, commercial controls use only. Operating temperature 0-40°C
(32-104°F), humidity maximum 90% (non-condensing).

Location

ETC recommends paying special attention to the installation environment:

When operating in PIR only modes, the sensor must have an
unobstructed view of the room. Do not mount behind or near tall
cabinets, shelves, hanging light fixtures, etc.

Do not install the sensor within eight feet from an HVAC airflow
duct/vent.

Install the sensor where it cannot easily sense movement in areas
outside of the intended space, such as hallways, glass partitions, or
adjacent rooms.

Note:

In areas of increased noise activity, enabling PIR only mode

may allow for better occupancy detection results. See

DIP Switches on

page 7

.

Dual Tech Wall-mount Vacancy Sensor

Page 2 of 12

ETC

Содержание Echo Dual Tech Wall-mount Vacancy Sensor













Отзывы: