ETAS ETK-T2.2G Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 61

ETAS ETK-T2.2G Скачать руководство пользователя страница 16

BR_XETK-S2.0 - User’s Guide

16

ETAS

Hardware Description

4

Hardware Description

In this chapter, the function blocks and the interfaces of the ETK-T2.2G are
explained in detail.

4.1

ETK-T2.2G Versions

The ETK-T2.2G can only be ordered in current variant "G". It is prepared for
different functional and mechanical versions, which can be released as new

products (name and order no.) on request.
The PCB is prepared for following improvements

• The LFBGA292 adapter could be replaced by an LFBGA516 adapter to fit

into an LFBGA516 socket for an TC1798

• The DPR could be extended to 2 MByte per page.

4.2

Architecture

Fig. 4-1 "ETK-T2.2G Architecture" shows the block diagram of the ETK-T2.2G.
The connection to the ECU is made by an LFBGA connector.

Fig. 4-1

ETK-T2.2G Architecture

The microcontroller can read via the BGA connector from one of the two pages
of the data emulation memory and can write its data directly to the measure-
ment data memory. These two memories (data emulation memory, measure-
ment data memory) are using the same address space and are realized inside the
same DPRs. Through the BGA connector the microcontroller can communicate
with other external memories or peripheral components too. All microcontroller
signals are accessible on the BGA connector.
While the microcontroller accesses the program data (not the program code) out
of the data emulation memory, the content of the data emulation memory can
simultaneously be modified by the calibration and development system through
the serial ETK-interface. This process enables adjustments of parameters, charac-
teristic lines and maps through the calibration and development system. Using

LFBGA292

Adapter

for TC1791

ETK-T2.2G

FLASH

1024 KB

(Data)

RAM
4 KB

System

Functions

Tool Interface

Trigger

Unit

Control

Unit

Automatic

Page

Initialization

Automatic
Power-On

U-Batt

ETK
Interface

100
Mbit/s

Power

Supply

Monitoring

Power

Supply

4.3...18 V

Standby

Power

Supply

4.3...18 V

ECU

Reset &

Power

Control

Sense ECU Power Supply

Standby Power Supply

ECU Reset

Ethernet

Phy

Ethernet

Traffic

Detection

LFBGA516

Socket

for TC1798

DPRAM

1024 KB

(Data Reference

Page +

Measurement)

DPRAM

1024 KB

(Data Working

Page +

Measurement)

JTAG

Debug
Interface

«
...
14
15
16
17
18
...
»

Содержание ETK-T2.2G






























































Отзывы:

Нет отзывов