ETAS ES5321.1 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 42

ETAS ES5321.1 Скачать руководство пользователя страница 12

ES5321.1 PWM I/O Board (48/32-CH) - User’s Guide

12

Introduction

ETAS

De-energizing the Add-on Card

Switch off the ES5300.1-A Housing or the ES5300.1-B Housing and external
power supplies, and unplug the power plug and other connectors attached to
the add-on card. Wait at least three minutes before removing the add-on card.

Approved Cables

The signal lines must not exceed a maximum length of 3 m.

Requirements for the installation location

Requirements for ventilation

Transport and Installation

To avoid damages to the hardware from electrostatic discharge, please observe
the following precautionary measures:

WARNING!

Fire hazard!
Use only approved cables for creating cable assemblies (e.g. for con-
necting the ECU and external loads). The cables used must, in partic-
ular, be suitable for the currents, voltages and temperatures which
occur and must be flame-retardant in accordance with one of the
following standards IEC60332-1-2, IEC60332-2-2, UL2556/
UL1581VW-1!

WARNING!

This is class A equipment. This equipment can cause radio interfer-
ence in residential areas. Should that be the case, the operator may
be requested to institute reasonable measures.

CAUTION!

The air circulation inside the ES5300.1-A Housing or the ES5300.1-B
Housing can be ensured only if all free slots are covered with front
plates. Otherwise, it may lead to overtemperatures and trip the over-
temperature protection of the ES5300.1-A or ES5300.1-B. For this
reason, install front plates in all free slots!

CAUTION!

Some components of the ES5321.1 can be damaged or destroyed by
electrostatic discharges. Leave the plug-in card in its transport pack-
aging until it is installed. Only remove, configure and install the
ES5321.1 at a workplace that is protected against electrostatic dis-
charges.

«
...
10
11
12
13
14
...
»

Содержание ES5321.1











































Отзывы:

Нет отзывов