eta PelletsCompact Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 68

eta PelletsCompact Скачать руководство пользователя страница 38

38

www.eta.co.at

Cables

Installation

Turn the changeover valve into the correct
position

In buffer operation of the boiler, switching between the
heating circuit and the hot water tank is no longer
needed. Therefore, remove the actuator from the
changeover valve.

Fig. 10-19: Actuator for changeover valve

Turn the changeover valve manually so that the
flow line to the hot water tank is blocked. See the

following illustration.

Fig. 10-20: correct position of the changeover valve

The actuator is no longer required. You can
disconnect its cable from the circuit board and

leave it on the boiler.

10.5

Cables

Connecting the boiler to potential equalisation

The boiler must be connected to the potential equaliza-
tion of the boiler room or the building. Country-specific
regulations must be observed while doing this.

Fig. 10-21: Connecting the potential equalisation

The bottom of the boiler features holes to connect
the potential equalisation (minimum cross-

section 6 mm²).

10.6

Filling the heating system

Filling the heating system

Fill the boiler via the fill/drain valve. The current system
pressure is shown on the pressure gauge.

«
...
36
37
38
39
40
...
»

Содержание PelletsCompact





































































Отзывы:

Нет отзывов