Eta COMPUTE SPCO0 Скачать руководство пользователя страница 15

 

 

 

 

 

 

 

 

Compliance Documentation 

Model # :  SPCO0 
Part # AS0010vA 
FCC ID : 2A7JIN-SPCO0 
IC: 28771-SPCO0 
Manufacturer:  

Eta Compute, Inc.   

WWW.etacompute.com

 

European Representative:  
 

Another Trail 

 

5 Ailee de Troenes 

 

38640 Claix, France 

 

Caution: the user is cautioned that changes or modifications not expressly approved by the 
party responsible for compliance could void the user's authority to operate the equipment. 

This device complies with part 15 of the FCC rules and industry Canada license-exempt RSS 
standard(s). Operation is subject to the following two conditions: (1) this device may not 
cause harmful interference, and (2) this device must accept any interference received, 
including interference that may cause undesired operation. 

Le présent appareil est conforme aux cnr d’in

dustrie Canada applicables aux appareils radio 

exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :

 

(1) l’appareil ne doit pas produire de brouillage, et

 

(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectri

que subi, même si le 

brouillage est susceptible d’en compromettre le fonctionnement.

 

Note: this equipment has been tested and found to comply with the limits for a class b digital 
device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable 
protection against harmful interference in a residential installation. This equipment 
generates, uses and can radiate radio frequency energy and, if not installed and used in 
accordance with the instructions, may cause harmful interference to radio communications. 
However, there is no guarantee that interference will not occur in a particular installation. 

If this equipment does cause harmful interference to radio or television reception, which can 
be determined by turning the equipment off and on, the user is encouraged to try to correct 
the interference by one or more of the following measures: 

Содержание SPCO0

















Отзывы: