Essilor Instruments DELTA Скачать руководство пользователя страница 126

Страница: 126 / 187

10.

Ethernet network settings

◦

IP address: preset before leaving the factory

◦

Subnet mask: preset before leaving the factory

◦

Network gateway: never fill out

◦

MAC address: preset before leaving the factory -unchangeable

11.

Serial port (RS232C)

Press on this button to activate or deactivate:

◦

the serial port

◦

the Phi tracer

12.

Network series settings

They must be set up according to the connected software.

◦

Transmission speed

◦

Length of frame

◦

Parity

◦

Stop bit

◦

Flow control

13.

Internet connexion verification

14.

Reset to factory settings

Once the modification is made, press

to return to the work screen.

2. C

USTOMIZE

THE

TRACER

AND

THE

CENTERING

DEVICE

This section will enable you to customize the tracer according to your requirements:

•

Customising the working modes and display precision

(

p.129)

•

Choosing a decentration mode

(

p.131)

•

Customising the action bar

(

p.132)

•

Adjusting the brightness

(

p.134)

•

Set up centering compensation

(

p.135)

a. Working modes and display precision

This menu is used to customize the tracer-centerer-blocker to suit your work preferences:

•

the working mode

•

the measurement accuracy display,

•

the centering page zoom,

•

the blocking mode in the boxing center or optical center.

To reach this menu since your working screen, select

SER

ANUAL

> VIII. S

THE

PRODUCT

129

Delta - Edging System > V1- 02-2020

Содержание DELTA




























































































































































































Результаты поиска

Содержание DELTA

Отзывы:

Essilor Instruments DELTA, Руководство пользователя, Страница: 126 / 187

Результаты поиска

Содержание DELTA

Отзывы: