2. Now, insert the plug of the solar module into the socket of the spotlight
(protected by a rubber lid) (illustration 8). Switch on the spotlight via the
rocker switch. (ON) (illustration 9). The solar spotlight is now activated.
Note: The LED light is very bright. In order to avoid damage to the eyes, please
do not look directly into the light!
3. The spotlight may be adjusted horizontally and vertically as required.
4. The motion sensor may also be adjusted horizontally. The marking on the
housing of the motion sensor situated on the opposite site of the adjustment
knobs serves for the adjustment of the detection range. In doing so, the
notch is considered as the center of the detection range. The three adjusting
controllers are turned towards the back while the spotlight is in operation!
4.3 Setting options of the motion sensors:
1. Lux.:
Setting of the switching-on threshold of the PIR sensor.
- Min.: activation at night
- Max.: activation at day(light) and night
2. Sens.:
Setting of the sensitivity of the PIR sensor:
- Min.: detection range approx. 3 m
- Max.: detection range approx. 10 m
3. Time: Setting of the light ON time after the last detection:
- Min.: Approx. 20 sec. after every detection
- Max.: Approx. 58 sec. after every detection
Note: During the winter months please generally expect a shorter light ON time.
If the lamp should not shine on the first evening, please wait for a sunny day.
5. Exchange of the battery pack
After one to two years, the capacity of the battery pack will decrease. It is then
required to exchange the battery pack. A new battery pack is available in the
Internet (art. No.: 901008, NiMh 6 V/ 2400 mAh) under www.esotec.de.
1. Switch off the spotlight by moving the slide switch into the position „OFF“.
2. Disconnect the solar module and unscrew the safety screw at the bottom of
the spotlight (illustration 12).
3. You may remove the spotlight from the assembly platform by slightly lifting it
off (illustration 13).
4. Unscrew the two safety screws at the back side of the spotlight and remove
the battery compartment cover (illustration 14).
5. Unplug the plug of the battery pack and remove the battery pack (illustrations
15 +16).
6. Re-insert the new battery pack and plug the plug on of the battery pack with
correct polarity.
7. Now close the housing in reverse order. When closing the lid, please make
sure that the gasket is positioned correctly. .
8. Mount the spotlight in its place and re-insert in the cable of the solar modules.
Put the switch back into position “ON”.
9. The spotlight is now ready for operation again.
Note: Used batteries or accumulators must be disposed of in a non-polluting
way and do not belong into the domestic waste. Your dealer is legally obliged to
take back the old accumulators.
6. Malfunctions
The lamp is not activated at darkness
- is the lamp switched on?
- A source of extraneous light (e.g. street lamp) simulates daylight and prevents
the activation. Place the lamp at a darker place or change the setting „Sens“.
The lamp is not switched on at darkness at all or only for a short time?
- Is the battery pack inserted?
- Is the spotlight switched on
- Battery weak or defective?
Exchange of the battery pack every 2 years at the latest!
Lamp is activated at night again and again without any movement of
persons:
- Are there any domestic or wild animals within the detection range? Possibly
change the setting „Sens“!
- Are there any large trees within the detection range which may possibly
cause temperature variations within the detection range? Possibly change
the setting „Sens “!
- Corner mounting? In case of corner mounting and occurring winds it may
happen that the temperature of the sensor varies which may result in faulty
switching operations. Possibly change the setting „Sens “ or look for another
place of installation!
7. Technical Data
Solar module:
• Solar cells:
Polycrystalline behind glass
(manufacturer: Kyocera)
• Capacity:
2 Wp
• Nominal voltage:
7,7 V
• Nominal current:
245 mA
• Type of protection:
IP 44
• Protection class:
III
• Operating temperature:
-20°C to +40°C
• Cable length:
5 m
LED spotlight:
• Luminous flux:
500 lm
• Light color:
2800 K (warm white)
• Max. detection range PIR sensor: 140°/ 10 m
• Twilight switch (LUX):
Adjustable: day and night until night
• Light ON time after detection:
Adjustable: 20 sec. to 58 sec.
• Sensitivity setting:
Adjustable: 3 m to approx. 10 m
• Light ON time:
in total max. 2 hours with a fully
charge battery pack
• Type of protection:
IP 44
• Protection class:
III
• Operating temperature:
-20°C to +40°C
• Operating voltage:
6 V
• Battery pack:
NiMh 6 V/ 2000 mAh
(spare part art. No: 901008, www.esotec.de)
Copyright, Änderungen vorbehalten!
14
15
16
8
9
slide switch
10
11
marking
1
3
2
12
13
