manualshive.com logo in svg

ESCO Technologies ETS-Lindgren EMGen 7003-003, Руководство пользователя, Страница: 32 / 55

Поделиться
Скачать
ESCO Technologies ETS-Lindgren EMGen 7003-003 Скачать руководство пользователя страница 32

32

 

EMGen Command Set

 

ets-lindgren.com 

 

AM:DEPT:MAX? 

Description: 

Gets the maximum amplitude modulation depth as a %. 

Syntax: 

[:SOURce]:AM[:DEPTh]:MAXimum?  

Example: 

Write: 

AM:DEPT:MAX?

  

Response: 

:AM:DEPT:MAX 100.0

 

 

AM:DEPT:MIN? 

Description: 

Gets the minimum amplitude modulation depth as a %. 

Syntax: 

[:SOURce]:AM[:DEPTh]:MINimum? 

Example: 

Write: 

AM:DEPT:MIN?

  

Response: 

:AM:DEPT:MIN 0.0

 

 

AM:INT:FREQ 

Description: 

Sets the amplitude modulation frequency in Hz. The units default to Hz but can 
also be specified as KHZ, MHZ or GHZ. 

 

The value can also be increased or decreased by step size:  

UP = Increase amplitude modulation frequency by step size. 

DOWN = Decrease amplitude modulation frequency by step size. 

Use the AM:INT:FREQ:STEP command to change the current step size. 

Syntax: 

[:SOURce]:AM:INTernal:FREQuency <value><unit>|UP|DOWN 

Example: 

Write: 

AM:INT:FREQ 1000 

Write: 

AM:INT:FREQ 2 KHZ 

 

AM:INT:FREQ? 

Description: 

Gets the amplitude modulation frequency in Hz. 

Syntax: 

[:SOURce]:AM:INTernal:FREQuency? 

Example: 

Write: 

AM:INT:FREQ? 

 

Response: 

:AM:INT:FREQ 2000 

  

 

Содержание ETS-Lindgren EMGen 7003-003
























































Отзывы:

Нет отзывов