ESC G41T-M Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 56

ESC G41T-M Скачать руководство пользователя страница 25

19

Installing the Motherboard

LPT_H: Onboard parallel port header

This is a header that can be used to connect to the printer, scanner or other devices.

1

STROBE

14

ALF

2

PD0

15

ERROR

3

PD1

16

INIT

4

PD2

17

SLCTIN

5

PD3

18

Ground

6

PD4

19

Ground

7

PD5

20

Ground

Pin Signal Name Pin Signal Name

8

PD6

21

Ground

9

PD7

22

Ground

10

ACK

23

Ground

11

BUSK

24

Ground

12

PE

25

Ground

13

SLCT

26 Key

Installing a Hard Disk Drive/CD-ROM/SATA Hard Drive

This section describes how to install IDE devices such as a hard disk drive and a CD-
ROM drive.

About IDE Devices

Your motherboard has one IDE channel interface. An IDE ribbon cable supporting
two IDE devices is bundled with the motherboard.

You must orient the cable connector so that the pin1 (color) edge of
the cable corresponds to the pin 1 of the I/O port connector.

IDE: IDE Connector

This motherboard supports four high data transfer SATA ports with each runs up to
3.0 Gb/s. To get better system performance, we recommend users connect the CD-
ROM to the IDE channel, and set up the hard drives on the SATA ports.

«
...
23
24
25
26
27
...
»

Содержание G41T-M

























































Отзывы:

Нет отзывов