esatto.house
9
Getting Started
Installation
Unpacking
• Packaging materials:
This appliance has been packaged to protect it against transportation damage.
Remove all packaging materials from around and inside the appliance and keep the original packaging
carton and materials in a safe place. It will help prevent any damage if the product needs to be
transported in the future, and you can use it to store the appliance when it is not in use. In the event the
carton is to be disposed of, please recycle all packaging materials where possible.
•
Suffocation:
Plastic wrapping can be a suffocation hazard for babies and young children, so ensure all
packaging materials are out of their reach and disposed of safely.
• Power cord:
Unwind the power cord to its full length and inspect it for damage. Do not use the appliance
if it or its cord have been damaged or are not working properly. In case of damage, contact our after sales
support line for advice on examination, repair or return of the damaged product.
• Read the manual:
Read this manual to familiarise yourself with the appliance. Pay particular attention to
the safety instructions on the previous pages.
• Clean:
To remove any dust from transit and storage, clean the interior and exterior surfaces of the
appliance with lukewarm water and a soft cloth. Dry thoroughly.
Important:
do not use harsh or abrasive
detergents or powders as these will damage the finish.
• Two person installation:
Use two or more people to move and install the appliance. Failure to do so can
result in back or other injury.
• Freestanding design:
This appliance is designed to be freestanding only, and should not be recessed or
built-in.
• Placement:
This appliance must be properly positioned on a dry, sturdy, level surface that is strong
enough to support it when it is fully loaded. It should be placed in an indoor area that is well ventilated.
• Ambient temperature:
The ambient temperatures must correspond to the climate class (
T
) indicated on
the rating plate of the appliance: 16° C – 38° C
• Clearances:
Ensure that air can circulate freely around the back of the cabinet,
which is necessary to cool the compressor and condenser. Allow at least 10cm clear
space at the back, 10cm at the sides of the unit and 30cm between the top and any
surface above (i.e. a bench top). If you are installing your refrigerator next to a fixed
wall, leave sufficient space on the hinge side to allow for the door to swing open.
Right Diagram: refrigerator dimensions including door swing.
Do NOT
install/use the appliance in the following locations/situations:
• In moist areas or areas of high humidity.
• In a recreational vehicle, or for use with an inverter.
• In direct sunlight, near heat sources, next to an open flame, cooking or heating appliance, or near any
other source of high heat.
• Direct sunlight may affect the acrylic coating and heat sources may increase the unit’s power
consumption. For best energy efficiency install the appliance in the coolest area of the room.
• In an area with extreme cold ambient temperatures.
• In an area with excessive moisture and high humidity. Make sure it is protected from elements such as
wind, rain, water spray or drips.
• In an area where petrol or other explosive and/or flammable liquids or fumes are used or stored. The
fumes can create a fire hazard or explosion.
2 4 Changing the Light
.
2.6 Energy saving tips
2
.
5
Starting
10
The appliance should be located in the coolest area of the room, away from heat producing
appliances or heating ducts, and out of the direct sunlight.
Let hot foods cool to room temperature before placing in the appliance. Overloading the appliance
forces the compressor to run longer. Foods that freeze too slowly may lose quality, or spoil.
Be sure to wrap foods properly, and wipe containers dry before placing them in the appliance.This
cuts down on frost build-up inside the appliance.
Appliance storage bin should not be lined with aluminum foil, wax paper, or paper toweling. Liners
interfere with cold air circulation, making the appliance less efficient.
Organize and label food to reduce door openings and extended searches. Remove as many items
as needed at one time, and close the door as soon as possible.
Any replacement or maintenance of the LED lamps is intended to be made by the manufacturer, its
service agent or similar qualified person.
(The picture above is only for reference.The actual configuration will depend on the physical product
or statement by the distributor)
Before putting any fresh or frozen foods, the refrigerator shall have run
for 2-3 hours, or for above 4 hours in summer when the ambient
temperature is high.
Spare enough space for convenient opening of the doors and drawers or
statement by the distributor.
Before initial start, keep the refrigerator still for t
wo
hour
s
before connecting it to
power supply.
7) Install the freezer door on the middle hinge, and install the
upper hinge, hinge cover and hole
cover.
hole cover
upper hinge
hinge
cover
screw
135
°
978mm
545mm
545mm
929mm
