ES&S DS850 Скачать руководство пользователя | Manualshive

Страница: 23 / 199

background image

Chapter 2: Safety Information

17

EVS5200_DOC_SOP_DS850

Software Version 2.10

Published: February 26, 2014

Chapter 2: Safety Information

When used properly, the DS850 is safe and effective. The following symbols, used
throughout this manual, indicate when hazards may occur during normal operation of
the scanner. Read the warnings and proceed with caution when you carry out potentially
hazardous scanner operations.

Important Safety Instructions

Please read all safety instructions before operating the DS850. Carefully follow all
instructions and heed all warnings.

Power Sources

Operate this product only from the type of power source indicated in this manual. Make
sure that the installation complies with applicable sections of the National Electric Code.
Consult your local building code before installing. See

Facilities, Furnishings, and

Fixtures Required for DS850 Operation

for more information.

Ventilation

Slots and openings in the case of the DS850 are included to provide adequate
ventilation for the unit. These openings must remain clear. Do not block or cover any
openings in the DS850 case; otherwise, the unit could overheat. Do not operate the
DS850 in an enclosed housing not approved by ES&S.

Warning Icons

Symbol

Definition

Electrical Shock Danger:

This symbol indicates a danger of electric shock. There are high

voltages present inside the enclosure of DS850 scanner. To reduce the risk of fire or elec-
tric shock, do not attempt to open any enclosures or gain access to areas for which you
have not been trained. Only ES&S qualified personnel should open enclosed areas of the
scanner.

Warning:

This user caution symbol indicates that damage to the scanner or injury to the

user could occur if the proper procedures are not followed. Carefully follow all instruc-
tions and proceed with caution when this symbol is associated with a set of instructions.

Caution:

Keep fingers, hands, and loose clothing clear of the areas where this symbol is

displayed.

«
...
21
22
23
24
25
...
»

Содержание DS850








































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DS850

Бренд: Parker Страницы: 5

Бренд: Wasp Страницы: 50

Бренд: Twiflex Страницы: 5

Бренд: SCHUNK Страницы: 24

Бренд: IEMCA Страницы: 212

OPENVISION HD OVHD-NDT-70

Бренд: QSA Global Страницы: 43

Бренд: Hakko Electronics Страницы: 4

Бренд: LANCIER Monitoring Страницы: 56

Бренд: Nordmann Engineering Страницы: 16

Xcomfort CSEZ-01/13

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 2

V Panel Express

Бренд: Kontron Embedded Computers Страницы: 38

Бренд: Kontron Embedded Computers Страницы: 86

Бренд: SAS Страницы: 22

Tri-Lobe TL Series

Бренд: Blower Engineering Страницы: 23

Бренд: AFM Страницы: 46

Бренд: Welker Страницы: 33

Бренд: Blacoh Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды