manualshive.com logo in svg

ESAB TAF 1251, Инструкция по эксплуатации

Поделиться
Скачать
ESAB TAF 1251 Скачать руководство пользователя страница 11

5 OPERATION

0449 510 101

- 11 -

© ESAB AB 2018

5

OPERATION

General safety regulations for handling the equipment can be found in the "SAFETY"
chapter of this manual. Read it through before you start using the equipment!

WARNING!
Never

use the welding power source without side plates.

NOTE!

The power source must be set to analogue mode to use the PEI control unit.

5.1

Controls

The front panel contains:

1.

Main circuit-breaker for switching the mains voltage and the fan on and
off in the welding power source.

• Position "1" On
• Position "0" Off

2.

• The indicator lamp (white) illuminates when the main switch is

switched on.

3.

Indicator lamp for overheating (yellow)

• The indicator lamp illuminates when the thermal cutout is deployed

due to excess temperature in the welding power source.

• The indicator lamp goes out when the temperature in the welding

power source has decreased to a permitted level.

4.

Pushbutton resetting the automatic fuse FU2 for 42 V supply voltage.

Содержание TAF 1251





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды