ESAB Sentinel A50 Скачать руководство пользователя страница 9

Страница: 9 / 12

TECHNICAL SPECIFICATION

Optical Class:

1 / 1 / 1 / 2

Viewing Area:

100 x 60 mm (3.94" x 2.36")

Arc Sensor:

Light State:

DIN 4

Grind State:

DIN 4

Cutting Mode:

Shade No. from 5 to 9

Welding Mode:

Shade No. from 9 to 13

Shade Control:

Internal, Variable Shade, Digital Touch Control

Power On/Off:

Automatic On / Off

Sensitivity Control:

Low — High, Digital Touch Control

UV/IR Protection:

Up to Shade DIN13 at all times

Power Supply:

Solar cell. Battery replaceable
2 × CR2450 lithium battery

Switching Time:

1/25,000 s. from Light to Dark

Oxyfuel Gas Welding

Yes

Oxygen Cutting

Yes

Grinding:

Yes

Delay (Dark to Light):

0.1 ~ 1.0 s Digital Touch Control

Low Amperage TIG Rated:

≥ 2 amps (DC); ≥ 2 amps (AC)

Operating Temp.:

-5 °C ~ +55 °C (23 °F ~ 131 °F)

Storing Temp.:

-20 °C ~ +70 °C (- 4 °F ~ 158 °F)

Helmet Material:

High Impact Resistance Nylon

Application Range:

Stick Welding (SMAW); TIG DC&AC; TIG Pulse DC;
TIG Pulse AC; MIG/MAG/CO2; MIG/MAG Pulse;
Plasma Arc Cutting (PAC); Plasma Arc Welding
(PAW); Air Carbon Arc Cutting (CAC-A); Oxyfuel Gas
Welding (OFW); Oxygen Cutting (OC); Grinding

Approved:

DINplus, CE, EN175, EN 379, EN166, ANSI Z87.1,
CSA Z94.3, AS/NZS 1338.1

fig. 11a fig. 11b

fig. 12a

fig. 12b

Содержание Sentinel A50













Результаты поиска

Содержание Sentinel A50

Отзывы:

Бренды по названию

Популярные бренды

ESAB Sentinel A50, Инструкция по эксплуатации

Результаты поиска

Содержание Sentinel A50

Отзывы:

Бренды по названию

Популярные бренды