background image

 

19 

LIMITED WARRANTY 

 

Erskine  Attachments,  LLC  warrants  each  new  machine  manufactured  by  us  to  be  free  from 
defects in material and workmanship for a period of twelve (12) months from date of delivery to 
the original purchaser. 
 
Our  obligation  under  this  warranty  is  to  replace  free  of  charge,  at  our  factory  or  authorized 
dealership, any part proven defective within the stated warranty time limit. 
 
All  parts  must  be  returned  freight  prepaid  and  adequately  packaged  to  prevent  damage  in 
transit. 
 
This warranty does not cover: 

1. 

New products which have been operated in excess of rated capacities or negligence 

2. 

Misuse, abuse, accidents or damage due to improperly routed hoses 

3. 

Machines  which  have  been  altered,  modified  or  repaired  in  any  manner  not 
authorized by our company 

4. 

Previously owned equipment 

5. 

Any  ground  engaging  tools  in  which  natural  wear  is  involved,  i.e.  tooth tips,  cutting 
teeth, etc 

6. 

Normal maintenance 

7. 

Fork tines 

8. 

Hydraulic motors that have been disassembled in any manner 

 
In no event will the Sales Representative, Dealership, Erskine Attachments, LLC, or any other 
company affiliated with it or them be liable for incidental or consequential damages or injuries, 
including but not limited to the loss of profit, rental or substitute equipment or other commercial 
loss.  Purchaser’s sole and exclusive remedy being as provided here in above. 
 
Erskine Attachments, LLC must  receive immediate notification of defect and no allowance  will 
be made for repairs without our consent or approval. 
 
This warranty is in lieu of all other warranties, express or implied by law or otherwise, and there 
is no warranty of merchantability or fitness purpose. 
 
No  agent,  employee,  or  representative  of  Erskine  Attachments,  LLC  has  any  authority  to  bind 
Erskine Attachments, LLC to any warranty except as specifically set forth herein.  Any of these 
limitations  excluded  by  local  law  shall  be  deemed  deleted  from  this  warranty;  all  other  terms 
apply. 
 
This  warranty  may  not  be  enlarged  or  modified  in  any  manner  except  in  writing  signed  by  an 
executive  officer  of  Erskine  Attachments,  LLC  to  improve  its  products  whenever  it  is  possible 
and practical to do so.    Erskine Attachments, LLC reserves the right  to make changes and or 
add  improvements  at  any  time  without  incurring  any  obligation  to  make  such  changes  or  add 
such improvements to products previously sold.  
 

 

 

 

 

 

 

 

 

 

Erskine Attachments, LLC 

P.O. Box 1083 Alexandria, MN 56308 

Phone (218) 435-4045 

 

 

Содержание 1070608





















Отзывы: