background image

10

3BA00253-01 

 2021-05-17 

 Rev. 1 

Ersa i-CON 1V & i-CON 1VC

6. 

Troubleshooting

6.1 

General errors

If the soldering station is not working as expected, please check the following points:

•  Is line voltage available? Properly connect the power cord to the 

equipment and the power point.

• 

Is the fuse defective? The fuse is located on the back of the equip

-

ment in the mains connection socket.

• 

Please observe that a defective fuse may also indicate a deeper 

cause of failure. Simply changing the fuse is, therefore, generally not 

sufficient.

•  Is the soldering tool properly connected to the supply unit?

6.2 

Error messages

The i-CON 1V carries out fault diagnoses independently. 
The result of a diagnosis is output as an error code: In this 
case, the triangular pictogram 

 appears in the display 

of the soldering station. The error code 

 is shown as a 

number between 2 and 99. 

An info note 

 is also displayed in the bottom line. For error codes, please refer to the 

error code table in the operating instructions. Error messages must be acknowledged 
through the i-OP. The connected soldering tool will be heated again only after the error 

has been acknowledged and eliminated.

Troubleshooting

Содержание i-CON 1V















Отзывы: