8 - RELAYS OPERATING MODE SETTING
10
11
9 - MEMORY MANAGEMENT
Esempio
:
Led lighting sequence: LR, LV, LV, LV, LR, LR LR, LR
Result number: 0 +0 +4 +8 +0 +0 +0 +0 = 12
Then the transmitter occupies the 12th position of the memory.
Tab. 3
Led lit
1°
2°
3°
4°
5°
6°
7°
8°
Green led weight
1
2
4
8
16
32
64
128
Red led weight
0
0
0
0
0
0
0
0
Tab. 2
Beep1
Beep3
Before the end of
the beep, press for
an istant P1, the led
DL1 will turn off
Press P3 for 3 sec.,
The led DL3 lights,
the buzzer sounds
“Beep3”
Beep1
Beep4
Press for an instant
P1, DL2 turns off
Press for 4 sec. P4: DL1
and DL4 will light and
the buzzer sounds Beep4
9B) - Display of the programmed delay of each relay
It is possible to display the delay time planned on the relay programmed as delayed.
Procedure:
Press for 4 sec the button corresponding to the relay which has to be check; press then in sequence:
P4
for
1 sec. and then
P3
for one instant. At this point a sequence of 8 lightings of the leds LD1 and LD2
commences: referring to that it is possible to calculate the planned delay. The number shown by the
sequence is given by the Tab.2.
Impulsive
DL1 DL2 DL3
Bistabile
Delayed
Impulsive with reduction
DL1 DL2 DL3
Bistable with reduction
Delayed with reduction
8D ) Range reduction removal
Repeat the above procedure and verify that the led DL4 turn-off at the end.
Press P1 for 4 sec ,
the led DL1 remains
lit; the buzzer sounds
“Beep1”
Press P2 for 4 sec ,
the led DL2 remains
lit; the buzzer sounds
“Beep1”
8E ) Relay release time programming
The release time after which the relay programmed as delayed releases is programmable.
The value of the time can be introduced making use of the buttons P1 and P2. Through 8 pressures
on P1 and P2, to which correspond as many lightings of the leds DL1(Red) and DL2 (Green), it is
possible to introduce a number in binary coding that gives the value of the delay.
Procedure:
- Press for 4 sec. the button corresponding to the relay to which you want to modify the delay time;
The configuration led lights on; subsequently press P3: the leds lit will turn off; after begin the
sequence of 8 pressures off P1 and P2 in base to the desired time and according to Tab.2. An
acoustic signal points out the end of the procedure
Pressioni tasti
1°
2°
3°
4°
5°
6°
7°
8°
Secondi
1
2
4
8
16
32
P1
P1
Secondi
10
20
40
80
160
320
P2
P1
Minuti
2
4
8
16
32
64
P1
P2
Minuti
20
40
80
160
320
640
P2
P2
One pressure on P1 has weight 0 while one pressure on P2 has weight 1. So, once finished all the
pressures concerning to the chosen value, it isn’t necessary to effect the remaining pressures on P1
Example 1
= 8 sec. delay : introduce the sequence : P1 - P1 - P1 - P2 - P1 - P1 - P1 - P1.
Example 2
= 2 min. delay: introduce the sequence : P2 - P1 - P1 - P1 - P1 - P1 - P1 - P2.
The relays can be programmed in 3 different modes: Impulsive (pre-planned), Bistabile (or step),
Delayed. For each of these possibilities it is possible besides to plan the
reduction
that
decreases the sensitivity of the receiver, preventing the receipt from great distance.
The configuration of each relay is displayed by the lighting of the corresponding led:
- DL1 points out that the relay is planned in impulsive mode;
- DL2 points out that the relay is planned in bistabile mode ;
- DL3 points out that the relay is planned in delayed mode;
- Besides DL4 points out that for the relay the range reduction has been activated.
While for the first 3 the three functions are in exclusive, the range reduction is an additional
functionality.
8A ) Relay operating mode display
Procedure:
Keep pressed down, for 4 seconds, the receiver button corresponding to the selected relay, up to the
acoustic signal; subsequently press for an instant
P4
, within 2 sec.; then still
P4
and check the lighting
of the leds.
Example
: RL1 relay operating mode display
Press for 4 sec. the button P1, for an instant P4, then still P4: the lighting of the leds gives the
operating mode set for RL1.
range
function
8B ) Change of the relays operating mode
Procedure:
for 4 sec. the button corresponding to the selected relay up to the acoustic signal;
will light ; within 2 sec. press the button
P1
and subsequently press the button
(P1, P2 or P3)
according to the new configuration to be planned: the first led will turn off and the
second will light on. Example: Change of the relay RL1 from impulsive to delayed:
Keep pressed down
the corresponding led
8C ) Range reduction programming
Example
: Range reduction of RL2 already programmed as impulsive.
Procedure:
Keep pressed down for 4 sec.the button corresponding to the selected relay up to the acoustic signal;
the corresponding led will light; within 2 sec. press the button
P1
and subsequently press the button
P4
. Besides the corresponding led will light also the led
DL4
.
9A) - Transmitter memory position display
It is possible to display the memory position of the last received transmitter.
Procedure:
Activate the transmitter ; then press in sequence : the button
P4
for 4 sec.,
P4
again for one instant and
then
P1.
The receiver begins a sequence of 8 lightings of DL1(red) and DL2 ( green), following pointed out
for simplicity as LR and LV: referring to that it is possible to find the memory position occupied by the code
just received. The number pointed out by the sequence of lightings is calculable by the following table:
T H E S M A R T L I V I N G
T H E S M A R T L I V I N G
