ermaf GP 40 ACU Скачать руководство пользователя страница 8

Страница: 8 / 24

GB-8

RUS

Setting mode

▷

Press and hold the MODE selection button when
the heater is switched off to go to Setting mode.

•

Switch off the heater

OFF

AUTO

+AUT

MODE

(RESET)

ON/OFF

▷

Mode E: eBus addresses can be saved.

Mode A/F: multi-functional outputs can be pa-

rameterized.

MFA 2

MFA 1

eBus address

Mode

MODE
button

eBus adddress

... eBus address

Save eBus address

Inactive

Fault (NC)

Fault (NO)

Operation

Standby

Inactive

Main fan

active

Main fan

inactive

Modulation

enable

> 2 s MODE button

OFF

▷

Press the RESET button to return to the previ-
ous menu.

▷

After a timeout of 20 s, the display will auto-

matically return to the initial mode. The display
indicates “–”.

Adjusting the heater

Burner gas pressure p

= Inlet pressure

= Gas pressure on the burner

▷

The gas pressure on the burner is adjusted using

on the combination control.

+ -

▷

For this, the outlet pressure p

must be meas-

ured on the combination control.



Disconnect the system from the electrical power

supply. The mains plug may only be pulled out
once the device has been switched off and post-
cooling is complete.



Shut off the gas supply.



Open pressure test point p

+ -

Switch on the power supply.

Release the gas supply.

▷

The inlet pressure p

must comply with the tech-

nical data, see page 23 (Technical data).

Switch on the burner control unit. Press the

ON/OFF button

OFF

AUTO

+ AUT

MODE

(RESET)

ON/OFF

until an LED lights up.

Select the Heating

operating mode.

Let all heaters burn for at least 20 s.

▷

The required gas pressure on the burner depends

on the heating value/Wobbe index.

Select the required gas pressure on the burner

from the tables:

Natural gas, LPG

Gas type

Heating

value

Wobbe

index

[mbar]

[MJ/m

]

Natural gas L G 25

32.49

41.53

13.5

Natural gas H G 20

37.78

50.71

9.5

LPG G 30

125.81

87.34

19.5

Содержание GP 40 ACU

























Результаты поиска

Содержание GP 40 ACU

Отзывы:

Похожие инструкции для GP 40 ACU

Бренды по названию

Популярные бренды

ermaf GP 40 ACU, Руководство по эксплуатации

Результаты поиска

Содержание GP 40 ACU

Отзывы:

Похожие инструкции для GP 40 ACU

Бренды по названию

Популярные бренды