manualshive.com logo in svg

Eriez HD-46C, Инструкции по установке, эксплуатации и обслуживанию, Страница: 12 / 12

Поделиться
Скачать
Eriez HD-46C Скачать руководство пользователя страница 12

©2019 Eriez All Rights Reserved

World Authority in Separation Technologies

 

Headquarters: 2200 Asbury Road, Erie, PA 16506-1402 U.S.A. 
Telephone: 814-835-6000 • Fax: 814-838-4960 
www.eriez.com e-mail: [email protected] 

Manufacturing Facilities: AUSTRALIA • BRAZIL • CANADA • CHINA • INDIA • JAPAN • MEXICO • SOUTH AFRICA • UNITED KINGDOM • UNITED STATES

 

 

519-AHA-Web

 

ERIEZ MANUFACTURING CO ©2019 

PRINTED IN USA

Eriez and Eriez Magnetics are registered trademarks of Eriez Manufacturing Co, Erie, PA

   

9.  Incorrect Tuning 

See maintenance instructions. To decrease 
displacement and output use fewer or thinner tuning 
springs. To decrease displacement and eliminate 
striking, use more or thicker tuning springs.

10.  Poor or Broken Weld on Tray 

Check and correct.

11.  Incorrect Factory Adjustment 

See maintenance instructions 
(Gap adjustments.)

12.  Sympathetic Vibration in Other Equipment 

Check and correct.

13.  Contact with Other Equipment 

Check and correct.

14.  Line Voltage or Hz Variation 

Check and install voltage regulator if necessary. 
Check Hz on output side of control. Adjust back to 
30 Hz per control manual.

15.  Blown Fuse or Circuit Breaker 

Check for short circuits and correct.

16.  Other Electrical Connections 

Check all connections and correct.

17.  Corrosive or Abrasive Material 

May require special tray. Consult Eriez.

18.  Product Variation 

If product density, moisture content or other 
characteristics vary, customer should take own 
corrective measures.

Troubleshooting 

(cont.)

Содержание HD-46C













Отзывы:

Нет отзывов