Ericsson C3 MAESTRO LBI-39101, Установка и настройка

Страница: 18 / 38

LBI-39101
18
PERSONAL COMPUTER
PC-To-Enhanced Audio Enclosure Serial Data
Interconnect Cable
The PC-to-Enhanced Audio Enclosure RS-232 serial
data link uses cable P29/5010150000 (350A1371P29). This
cable has a female DB-9 connector on one end for mating
to the PC's male DB-9 serial COM port connector. The
cable's other end has a male DB-9 connector for mating to
the female DB-9 connector labeled "
PC
" at the Enhanced
Audio Enclosure. The cable is ten (10) feet long. It should
not be modified in any way and "extension" cables are not
recommended for this 19.2k baud serial link. Identical
cables are also used between the Enhanced
Audio
Enclosure and the Speaker Assemblies.
❏
Mate the cable's female DB-9 connector to the
PC's male DB-9 serial COM port connector used
for Enhanced Audio Enclosure interfacing.
Normally, the COM2 port is used. Mate the other
end of the cable to the Enhanced
Audio
Enclosure's DB-9 connector labeled " PC ". This
interconnection is shown in Figure 1 but not in
Figure 6.
Standard PC Keyboard
During dispatch operations, the standard PC keyboard
is not used. However, during the console set-up process,
access to this keyboard will be required:
•
for file management (for example -
AUTOEXEC.BAT
and CONFIG.SYS file changes
may be necessary)
•
to configure certain items via the Editor program
(see LBI-39056 for details)
•
to start the console's application program
❏
Connect the standard PC keyboard to the PC in
accordance with the manufacturer's instructions.
Typically, the plug on the keyboard's cable mates
with a connector on the back of the PC.
Video Display Monitor
❏
Interconnect the video display monitor's video
cable to the Personal Computer in accordance with
the manufacturer's instructions.
ENHANCED AUDIO ENCLOSURE
All Enhanced Audio Enclosure interconnections are
made at the rear panel of the enclosure. Secure the cables
with cable ties as necessary.
Dispatch Keyboard
The Dispatch Keyboard interfaces to the console
system via the Enhanced Audio Enclosure. This keyboard's
part number is P29/7590182003 (350A1371P17). It is
sometimes referred to as the "custom keyboard".
❏
Connect the Dispatch Keyboard to the Enhanced
Audio Enclosure by plugging its male DB-9
connector to the female DB-9 connector on
Enhanced Audio Enclosure's rear panel. On the
rear panel, this connector is labeled "
KBD
". Its
pin-out is indicated in Table 24.
Desk Mic (if used)
❏
Connect the desk microphone (option CRMC3D or
equivalent) to the Enhanced Audio Enclosure by
mating its male DB-9 connector to the female
DB-9 connector labeled "
DESK MIC
" on the
Enhanced Audio Enclosure's rear panel. The desk
mic's cable is five (5) feet (1.52 meters) long. The
DB-9's pin-out is shown in Table 15.
Do not over-tighten the screws on the DB-style
connectors.
Headset Jacks (if used)
❏
At the selected location, secure each headset jack
box (part of option CRCN1W or equivalent) to the
mounting surface using the four (4) #10 thread-
forming screws supplied in the installation kit.
Before mounting, verify adequate clearance is
maintained for the headset's plugs. If using both
jack boxes, label them "SUPERVISOR" and
"OPERATOR".
❏
Connect each headset jack box to the Enhanced
Audio Enclosure using the 6-foot (1.83 meters)
cable supplied. This cable (part number
19C337102P1 supplied with CRCN1W) has male
DB-9 connectors on both ends. One end mates
with the female DB-9 connector at a headset jack
box and the other end mates to the female DB-9
connector at the Enhanced Audio Enclosure's rear
panel. The connectors on the rear panel are labeled
"
SUPER H/S
" and "
OPER H/S
" for the
supervisor and operator headsets respectively.
Interconnect the cables accordingly. The DB-9
connectors' pin-outs are indicated in Tables 16 and
17.
NOTE