Saf
et
y I
nstruc
tions
CAUTION:
This mount is intended for use only with the maximum weights
indicated. Use with flat screens heavier than the maximum indicated may
result in instability causing possible injury.
Do not attempt to install this product until all instructions and warnings have been read and
properly understood. Please keep these instructions for future reference. Please check carefully
to make sure there are no missing or defective parts – defective parts must never be used.
ErgoMounts Limited, its distributors and dealers are not liable or responsible for damage or injury
caused by improper installation, improper use or failure to observe these safety instructions. In such
cases, all guarantees will expire.
General
ErgoMounts Limited recommends that a professional AV installer or other suitably qualified person
install this product. Great care must always be taken during installation as most AV equipment is of
a fragile nature, possibly heavy and easily damaged if dropped.
If you do not fully understand the instructions or are not sure how to install this product safely,
then please consult a professional for advice and/or to install this product for you. Failure to mount
this product correctly may cause serious injury or death both during installation and at any time
thereafter.
Do not mount any AV equipment that exceeds the specific weight limit of the product you are
installing.
This weight limit will be clearly stated on each product and its packaging and will vary from product
to product.
Product Location
Please pay careful attention to where this product is located. Check the load capacity of wall prior to
installation as some walls are not suitable. Designed for indoor use, this mount is suitable for public
or home installation. If located in a public or frequently populated area ensure that the product is
out of the immediate reach of people. If any AV equipment is to be suspended over the likely path
or location of people then great care should be taken to secure all parts of the installation from
falling. If you install this product on drywall it must be securely fixed to a wooden stud, concrete
block or other permanent structure behind the drywall board. Installing on drywall boards alone
will not support the weight of most AV equipment.
When drilling holes in walls it is essential to avoid contact with electrical cables and water or
gas pipes contained within. Use of a good quality live wire detector and hidden object locator is
therefore recommended. Only drill intro structures when you are sure it is safe to do so.
Fixing Hardware
It is highly recommended that all wall fixing screws be used where supplied and that the purpose of
all other fixing hardware is fully understood. In some cases more AV equipment fixing hardware will
be supplied to accommodate different models of equipment and set up configurations.
The installer must be satisfied that any supplied fixing hardware is suitable for each specific
installation. If any fixing screws or included hardware is deemed not sufficient for a safe installation
then please consult a professional or your local hardware store.
Hazard Limitation
When routing cables, take advantage of any built in cable management features that the product
might provide and ensure that all cables are tidy and secure. Check to see that any moving aspect
of the product can do so unhindered by any cabling.
Some products have moving parts and the potential to cause injury through the crushing or
trapping of fingers or other body parts.
Particular attention to the nature of moving parts is required especially when assembling, installing
and adjusting during setup.
Immediately after installations double-check that the work done is safe and secure. Double-check
all necessary fixings are present and are of ample tightness.
It is recommended that periodic inspections of the product and its fixing points are made as
frequently as possible to ensure that safety is maintained. If in doubt consult a professional AV
installer or other suitably qualified person.
Содержание EMZ200
