manualshive.com logo in svg

Eramco Dust Free 3000 Series, Инструкция по установке и обслуживанию

Поделиться
Скачать
Eramco Dust Free 3000 Series Скачать руководство пользователя страница 8

ROOF MOUNT

The unit should be supported on beams or pads that are high enough so that water on

the roof cannot rise to the bottom of the unit. If 4"x4" timers are used, be sure that they

are both long enough to support the weight and oriented so as to transfer the weight of

the unit to the roof and the underlying support structure. If attachment to the support

structure is required, the floor or back side of the unit may be field drilled for bolts or

screws. Seal all penetrations with silicone rubber or butyl rubber to avoid water and air

leaks. Place bolts or screws where they will not interfere with filter insertion or removal.

Take care to locate the duct work so that the filter and motor are easily serviced. Locate

and shim the support beams or pads so they equally support the load.

PAD MOUNT

The unit should be supported on beams or pads that are high enough that water cannot

rise to the bottom of the unit and damage the filters or the motor. If 4"x4" timbers are

used be sure that they are both long enough to support the weight and oriented so as to

transfer the weight of the unit to the pad. Take care to place the duct work so that the

filters and motor are easily serviced. Locate and shim the support beams or pads so

they equally support the load.

8

INSTALLATION

Содержание Dust Free 3000 Series











Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды