Equipment Defender Backpack Blower Rack V2 Скачать руководство пользователя страница 3

Страница: 3 / 9

Step Four

Install the lock assembly onto the straight steel rod.

Tighten the bolts just enough to keep the lock assembly

from sliding down for now.

Step Five

Step Six

Lock assembly

Bent Steel Rod

Back Support

Bracket

The bent steel rod installs at an angle as shown

Install a collar then the securing bar then another collar onto the

bent steel rod. Lightly tighten the top collar for now it will be thread

locked and tightened very tight when adjusting the rack to fit your

blower. The screw head in the top collar can be packed with epoxy

after tightening for maximum security.

Securing bar

Securing Bar

Collar

•

Remove all set screws and apply thread lock before tightening.

•

Make sure all set screws are VERY tight.

•

Note: If you wish to achieve maximum security bolt/screw heads can be filled with epoxy.

1. Slide the bent steel rod through the back support

bracket and into the base.

2. Tighten a setscrew in the base just enough to keep

the rod in place for now.

Содержание Backpack Blower Rack V2










Результаты поиска

Содержание Backpack Blower Rack V2

Отзывы:

Похожие инструкции для Backpack Blower Rack V2

Бренды по названию

Популярные бренды

Equipment Defender Backpack Blower Rack V2, Руководство по сборке

Результаты поиска

Содержание Backpack Blower Rack V2

Отзывы:

Похожие инструкции для Backpack Blower Rack V2

Бренды по названию

Популярные бренды