manualshive.com logo in svg

Epson Stylus Photo R290, Руководство по обслуживанию, Страница: 77 / 125

Поделиться
Скачать
Epson Stylus Photo R290 Скачать руководство пользователя страница 77

EPSON Stylus Photo R280/R285/R290

Revision B

Chapter 4 Disassembly/Assembly

4.4.5 Waste Ink Tray (Disassembling the Printer Mechanism)

77

4.4.5  Waste Ink Tray

†

Parts/Components need to be removed in advance

Printer Cover / Paper Support Assy / Upper Housing / Main Board Unit / Panel Assy / 
Cover Open Sensor / Printer Mechanism

†

Removal procedure

1.

Remove the two screws, disengage the hook, and remove the Waste Ink Tray.

•

Screw

: C.B.P. M3x10 (tightening torque: 5-7 kgf.cm) 

(No.4)

Figure 4-61.  Removing the Waste Ink Tray

4.4.6  Waste Ink Pad

†

Parts/Components need to be removed in advance
Printer Cover / Paper Support Assy / Upper Housing / Main Board Unit / Panel Assy / 
Cover Open Sensor / Printer Mechanism

†

Removal procedure

1.

Remove the three Waste Ink Pads from the trays.

Figure 4-62.  Removing the Waste Ink Pad

C A U T I O N

When removing the Waste Ink Tray, take extra care not to spill 
ink and contaminate the printer and surroundings.

A D J U S T M E N T

R E Q U I R E D

Whenever the Waste Ink Tray is replaced, the required 
adjustments must be carried out.

•

Refer to "5.1.2 Required Adjustments" (p.99)

Waste Ink Tray

Hook

C A U T I O N

„

When removing the Waste Ink Pad, take extra care not to 
contaminate the printer and surroundings with ink.

„

Be careful of the seven sharp edges shown in 

Fig.4-62

 when 

disassembling or reassembling.

Insert the Waste Ink Pads into the trays inserting the slits of the 
pads over the tabs 

 on the trays. Make sure to push the pads as 

far as they will go (until their top surface locate lower than the top 
surface of the tray edges).

Figure 4-63.  Installing the Waste Ink Pad

A D J U S T M E N T

R E Q U I R E D

Whenever the Waste Ink Pad is replaced, the required 
adjustments must be carried out.

•

Refer to "5.1.2 Required Adjustments" (p.99)

Waste Ink Pad

Sharp edge

Slit

Tab

Содержание Stylus Photo R290






























































































































Отзывы:

Нет отзывов