Epson Stylus 1500 Скачать руководство пользователя страница 90

Страница: 90 / 185

Printer Mechanism (M-4E60) Disassembly

Procedures in this section explain how to remove components in the printer mechanism.

CAUTION

Never touch the white PF gears. Handling them will cause damage or contamination that
will affect print quality.

Cartridge Holder Unit

Remove the printer mechanism. (See page 3-9.)

Unclamp the cables for the ink cartridge sensor and black ink end sensor from the right frame.

Remove 2 (CBS 3

6) screws securing the cartridge holder to the right frame, and remove the

cartridge holder unit from the right frame, along with the ink supply tube.

CAUTION

Only remove the ink supply tube when necessary. If you need to disconnect it, be sure to
raise the end of the tube to prevent the ink from leaking out.

Remove the nut fastening the ink tube, and remove the tube from cartridge holder.

DISASSEMBLY/ASSEMBLY POINTS

❏

When you attach the ink supply tube, insert the nut used to fasten the tube first, and then
insert O-ring into the ink supply tube.

❏

Tighten the screws using a torque wrench. The tightening torque for the nut is
0.09 ~ 0.11 Nm (0.90 ~ 1.1 kg-cm).

Printer Mechanism

CBS 3 x 6

Cartridge Holder Unit

Ink Supply Tube

Nut Fastening the Ink Tube

O-ring

Righ t Frame

Figure 3-18. Removing the Cartridge Holder Unit

Disassembly and Assembly

EPSON Stylus 1500 Service Manual

3-21

Содержание Stylus 1500


























































































































































































Результаты поиска

Содержание Stylus 1500

Отзывы:

Похожие инструкции для Stylus 1500

Бренды по названию

Популярные бренды

Epson Stylus 1500, Руководство по обслуживанию

Результаты поиска

Содержание Stylus 1500

Отзывы:

Похожие инструкции для Stylus 1500

Бренды по названию

Популярные бренды