manualshive.com logo in svg

Epson S1C33L26, Техническое руководство

Эпсон S1C33L26 - микроконтроллер высокой производительности для различных приложений. Для получения технической документации, скачайте бесплатное руководство пользователя на нашем сайте. Техническое руководство доступно для скачивания на manualshive.com. Полезная информация для успешной работы с продуктом.

Поделиться
Скачать
background image

6  CLOCK MANAGEMENT UNIT (CMU)

6-12

 

Seiko Epson Corporation 

S1C33L26 TECHNICAL MANUAL

Peripheral Module Clocks (PCLK1, PCLK2)

6.7.3  

PCLK1

PCLK1_EN

MCLK

PCLK2

PCLK2_EN

7.3.1 PCLK Control Circuit

Figure 6.

The PCLK1 and PCLK2 clocks are used to operate the modules listed below.

7.3.1  Peripheral Modules and Operating Clocks

Table 6.

Clock

Clock enable bit

Peripheral modules

PCLK1

PCLK1_EN/CMU_CLKCTL register

• Prescaler (PSC Ch.0)
• 8-bit programmable timer Ch.0, 2, 4, 6 (T8 Ch.0, 2, 4, 6)
• 16-bit PWM timer Ch.0, 1 (T16A5 Ch.0, 1)
• 16-bit audio PWM timer (T16P)
• Universal serial interface (USI)
• Serial interface Ch.0 (FSIO Ch.0)
• A/D converter (ADC10)
• I

2

S (I2S)

• Misc registers (MISC)

PCLK2

PCLK2_EN/CMU_CLKCTL register

• Prescaler (PSC Ch.1)
• 8-bit programmable timer Ch.1, 3, 5, 7 (T8 Ch.1, 3, 5, 7)
• Universal serial interface with LCD interface (USIL) 
• Serial interface Ch.1 (FSIO Ch.1)
• Watchdog timer (WDT)
• Remote controller (REMC)
• Interrupt controller (ITC)
• I/O ports (GPIO)
• BBRAM
• Cache controller (CCU) registers
• Real-time clock (RTC) registers
• SRAM controller (SRAMC) registers
• SDRAM controller (SDRAMC) registers
• LCD controller (LCDC) registers

The peripheral module clock (PCLK1, PCLK2) supply can be controlled using the clock enable bit (PCLK1_EN, 
PCLK2_EN).
The default setting of the clock enable bit is 1, which enables the clock supply. Disable the clock supply by setting 
the clock enable bit to 0 to reduce current consumption unless all the modules that use the clock need to be running.
The clock is supplied even in HALT mode when the clock enable bit is set to 1. To stop the modules in HALT 
mode, set the clock enable bit to 0 before executing the halt instruction.
In SLEEP mode (when the slp instruction is executed), these clocks stop even if the clock enable bit is set to 1.

GE Module Clock (GCLK)

6.7.4  

GCLK

GCLK_EN

MCLK

7.4.1  GCLK Control Circuit

Figure 6.

The GCLK clock is the GE module operating clock. GCLK_EN/CMU_CLKCTL register is used for clock supply 
control. The default setting of GCLK_EN is 1, which enables the clock supply. Disable the clock supply by setting 
GCLK_EN to 0 to reduce current consumption when the GE functions are not used.
GCLK is supplied even in HALT mode when GCLK_EN is set to 1. To stop the GE module in HALT mode, set 
GCLK_EN to 0 before executing the halt instruction.
In SLEEP mode (when the slp instruction is executed), GCLK stops even if GCLK_EN is set to 1.

Содержание S1C33L26



















































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S1C33L26

FAAC 740 D User Manual preview
740 D
Бренд: FAAC Страницы: 64
Hable One Starting Manual preview
One
Бренд: Hable Страницы: 3
Raypak RayTemp Installation & Operating Instructions Manual preview
RayTemp
Бренд: Raypak Страницы: 24
J+J S 20 Handbook preview
S 20
Бренд: J+J Страницы: 91
WAC T24-OD-CTR Installation Instruction preview
T24-OD-CTR
Бренд: WAC Страницы: 5
Bailey infi 90 IMMFP12 Instruction preview
infi 90 IMMFP12
Бренд: Bailey Страницы: 75
bluelab Dosetronic Instruction Manual preview
Dosetronic
Бренд: bluelab Страницы: 39
Fairford Synergy SGY-101 Quick Start Manual preview
Synergy SGY-101
Бренд: Fairford Страницы: 20
ST UM1932 User Manual preview
UM1932
Бренд: ST Страницы: 40
Varian 969-9507 Instruction Manual preview
969-9507
Бренд: Varian Страницы: 37
ADLINK Technology PCIe-8332 User Manual preview
PCIe-8332
Бренд: ADLINK Technology Страницы: 37
Danfoss AME 15 QM Instructions Manual preview
AME 15 QM
Бренд: Danfoss Страницы: 14
zeeltronic PDCI-NS1V User Manual preview
PDCI-NS1V
Бренд: zeeltronic Страницы: 15
M-system M8BS2-081 Instruction Manual preview
M8BS2-081
Бренд: M-system Страницы: 3
DIG 410BT Series Instruction Manual preview
410BT Series
Бренд: DIG Страницы: 16
YOKOGAWA Revolution FA-M3 R Technical Information preview
Revolution FA-M3 R
Бренд: YOKOGAWA Страницы: 57
Technologic TLK 43 Operating Instructions Manual preview
TLK 43
Бренд: Technologic Страницы: 21
Danfoss AMD 610 AS Installation Manual preview
AMD 610 AS
Бренд: Danfoss Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды