manualshive.com logo in svg

Epson S1C33L26, Техническое руководство

Эпсон S1C33L26 - микроконтроллер высокой производительности для различных приложений. Для получения технической документации, скачайте бесплатное руководство пользователя на нашем сайте. Техническое руководство доступно для скачивания на manualshive.com. Полезная информация для успешной работы с продуктом.

Поделиться
Скачать
background image

12  INTERRUPT CONTROLLER (ITC)

12-6

 

Seiko Epson Corporation 

S1C33L26 TECHNICAL MANUAL

Control Register Details

12.7  

7.1  List of ITC Registers

Table 12.

Address

Register name

Function

0x300210 ITC_FPT03_LV

FPT0–3 Interrupt Level Register

Set FPT0–3 interrupt levels

0x300211 ITC_FPT47_LV

FPT4–7 Interrupt Level Register

Set FPT4–7 interrupt levels

0x300212 ITC_FPT8B_LV

FPT8–B Interrupt Level Register

Set FPT8–B interrupt levels

0x300213 ITC_FPTCF_LV

FPTC–F Interrupt Level Register

Set FPTC–F interrupt levels

0x300214 ITC_DMA02_LV

DMAC Ch.0 & 2 Interrupt Level Register

Set DMAC Ch.0 and 2 interrupt levels

0x300215 ITC_DMA13_LV

DMAC Ch.1 & 3 Interrupt Level Register

Set DMAC Ch.1 and 3 interrupt levels

0x300216 ITC_DMA46_LV

DMAC Ch.4 & 6 Interrupt Level Register

Set DMAC Ch.4 and 6 interrupt levels

0x300217 ITC_DMA57_LV

DMAC Ch.5 & 7 Interrupt Level Register

Set DMAC Ch.5 and 7 interrupt levels

0x300218 ITC_T16P_LV

T16P Interrupt Level Register

Set T16P interrupt level

0x300219 ITC_T16A0_LV

T16A5 Ch.0 Interrupt Level Register

Set T16A5 Ch.0 interrupt level

0x30021a ITC_T16A1_LV

T16A5 Ch.1 Interrupt Level Register

Set T16A5 Ch.1 interrupt level

0x30021b ITC_LCDC_LV

LCDC Interrupt Level Register

Set LCDC interrupt level

0x30021d ITC_T804_LV

T8 Ch.0 & 4 Interrupt Level Register

Set T8 Ch.0 and 4 interrupt levels

0x30021e ITC_T815_LV

T8 Ch.1 & 5 Interrupt Level Register

Set T8 Ch.1 and 5 interrupt levels

0x30021f ITC_T826_LV

T8 Ch.2 & 6 Interrupt Level Register

Set T8 Ch.2 and 6 interrupt levels

0x300220 ITC_T837_LV

T8 Ch.3 & 7 Interrupt Level Register

Set T8 Ch.3 and 7 interrupt levels

0x300221 ITC_USI_LV

USI Interrupt Level Register

Set USI interrupt level

0x300222 ITC_FSIO0_LV

FSIO Ch.0 Interrupt Level Register

Set FSIO Ch.0 interrupt level

0x300223 ITC_ADC10_LV

ADC10 Interrupt Level Register

Set ADC10 interrupt level

0x300224 ITC_RTC_LV

RTC Interrupt Level Register

Set RTC interrupt level

0x300226 ITC_FSIO1_LV

FSIO Ch.1 Interrupt Level Register

Set FSIO Ch.1 interrupt level

0x300227 ITC_USIL_LV

USIL Interrupt Level Register

Set USIL interrupt level

0x300228 ITC_REMC_LV

REMC Interrupt Level Register

Set REMC interrupt level

0x300229 ITC_I2S_LV

I

2

S Interrupt Level Register

Set I

2

S interrupt level

0x30022a ITC_GECOM_LV GE Complete Interrupt Level Register

Set GE complete interrupt level

0x30022b ITC_GEERR_LV

GE Error Interrupt Level Register

Set GE error interrupt level

0x30022c ITC_USB_LV

USB Interrupt Level Register

Set USB interrupt level

The ITC registers are described in detail below. These are 8-bit registers.

Note:  When data is written to the registers, the “Reserved” bits must always be written as 0 and not 1.

Interrupt Level Registers (ITC_

xxx

_LV)

Register name Address

Bit

Name

Function

Setting

Init. R/W

Remarks

Interrupt Level 
Register
(ITC_

xxx

_LV)

0x300210

|

0x30022c

(8 bits)

D7–3 –

reserved

–

–

–

0 when being read.

D2–0 INT_LV[2:0] Interrupt level

1 to 7

0x0 R/W

D[7:3] 

Reserved

D[2:0] 

INT_LV[2:0]: Interrupt Level Bits

 

Sets the interrupt level (1 to 7). (Default: 0x0)

 

The C33 PE Core does not accept interrupts with a level set lower than the PSR IL value.

 

The ITC uses the interrupt level when multiple interrupt requests occur simultaneously. 

 

If multiple interrupt requests enabled by the interrupt enable bit occur simultaneously, the ITC sends 
the interrupt request with the highest level set by the ITC_

xxx

_LV registers (0x300210 to 0x30022c) to 

the C33 PE Core.

 

If multiple interrupt requests with the same interrupt level occur simultaneously, the interrupt with the 
lowest vector number is processed first. The other interrupts are held until all interrupts of higher prior-
ity have been accepted by the C33 PE Core.

 

If an interrupt requests of higher priority occurs while the ITC outputs an interrupt request signal to the 
C33 PE Core (before acceptance by the C33 PE Core), the ITC alters the vector number and interrupt 
level signals to the setting details of the most recent interrupt. The immediately preceding interrupt is 
held.

Note:  Make sure that the PSR IE bit is set to 0 before setting the interrupt level registers (ITC_

xxx

_LV).

Содержание S1C33L26



















































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S1C33L26

Bartlett 700 Series Operation Manual preview
700 Series
Бренд: Bartlett Страницы: 30
ADEMCO MAX Programming Instructions preview
MAX
Бренд: ADEMCO Страницы: 2
CalAmp LMU 2630MB Installation Manual preview
LMU 2630MB
Бренд: CalAmp Страницы: 13
HomeMatic HmIP-FAL230-C10 Installation And Operaion Manual preview
HmIP-FAL230-C10
Бренд: HomeMatic Страницы: 42
Z-Wave AC MASTER LITE Installation Manual preview
AC MASTER LITE
Бренд: Z-Wave Страницы: 27
D+H VCD 203 Manual preview
VCD 203
Бренд: D+H Страницы: 16
CompuPro DISK 3 Technical Manual preview
DISK 3
Бренд: CompuPro Страницы: 33
SFC SFCR-MD Operation Manual preview
SFCR-MD
Бренд: SFC Страницы: 48
Satel KNX-SA41 Quick Installation Manual preview
KNX-SA41
Бренд: Satel Страницы: 8
National Instruments sbRIO-9698 User Manual preview
sbRIO-9698
Бренд: National Instruments Страницы: 12
Velp Scientifica F201A0505 Instruction Manual preview
F201A0505
Бренд: Velp Scientifica Страницы: 24
Aurora Scientific 315D Instruction Manual preview
315D
Бренд: Aurora Scientific Страницы: 21
Clare Controls CLIQ.host Installation Sheet preview
CLIQ.host
Бренд: Clare Controls Страницы: 3
Swegon TACTouch TAC5 Manual preview
TACTouch TAC5
Бренд: Swegon Страницы: 11
Leader F1620 Manual preview
F1620
Бренд: Leader Страницы: 46
Harsen GU641A Operation Manual preview
GU641A
Бренд: Harsen Страницы: 55
Wabtec Ricon 55914 Installation Instructions preview
Ricon 55914
Бренд: Wabtec Страницы: 5
Satel MTX-300 Manual preview
MTX-300
Бренд: Satel Страницы: 26

Бренды по названию

Популярные бренды

Загрузить еще бренды