Epson S1C17F13 Скачать руководство пользователя | Manualshive

Страница: 194 / 247

background image

20 Temperature Detection Circuit (TEM)

20-2

Seiko epson Corporation

S1C17F13 TeChniCal Manual

(Rev. 1.0)

Clock Settings

20.2

TEM Operating Clock

20.2.1

When using TEM, the TEM operating clock CLK_TEM must be supplied to TEM from the clock generator. The
CLK_TEM supply should be controlled as in the procedure shown below.
1. Enable the clock source in the clock generator if it is stopped (refer to “Clock Generator” in the “Power Supply,

Reset, and Clocks” chapter).

2. Set the following TEMCLK register bits:

- TEMCLK.CLKSRC[1:0] bits (Clock source selection)
- TEMCLK.CLKDIV[1:0] bits (Clock division ratio selection = Clock frequency setting)

Clock Supply in SLEEP Mode

20.2.2

When using TEM during SLEEP mode, the TEM operating clock CLK_TEM must be configured so that it will
keep supplying by writing 0 to the CLGOSC.

xxxx

SLPC bit for the CLK_TEM clock source.

Clock Supply in DEBUG Mode

20.2.3

The CLK_TEM supply during DEBUG mode should be controlled using the TEMCLK.DBRUN bit.
The CLK_TEM supply to TEM is suspended when the CPU enters DEBUG mode if the TEMCLK.DBRUN bit =
0. After the CPU returns to normal mode, the CLK_TEM supply resumes. Although TEM stops operating when the
CLK_TEM supply is suspended, the registers retain the status before DEBUG mode was entered. If the TEMCLK.
DBRUN bit = 1, the CLK_TEM supply is not suspended and TEM will keep operating in DEBUG mode.

Operations

20.3

Initialization

20.3.1

TEM should be initialized with the procedure shown below.
1.  Set the TEMCLK.CLKSRC[1:0] and TEMCLK.CLKDIV[1:0] bits.  (Configure operating clock)
2.  Set the TEMTMG.CVTM[7:0] bits.

(Set comparison time)

3. Set the following bits when using the interrupt:

- Write 1 to the TEMINTF.TEMIF bit.

(Clear interrupt flag)

- Set the TEMINTE.TEMIE bit to 1.

(Enable interrupt)

Comparison Time Setting

20.3.2

Set the time for comparing each comparison voltage by the comparator to the TEMTMG.CVTM[7:0] bits.
Be sure to set a 150 µs or more comparison time including clock frequency dispersion.

CVTM + 1

Comparison time = ——————

≥

150 [µs]

(Eq. 20.1)

CLK_TEM

Where

CVTM:

TEMTMG.CVTM[7:0] bit setting value (0 to 255)

CLK_TEM: CLK_TEM frequency [Hz]

«
...
192
193
194
195
196
...
»

Содержание S1C17F13
























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S1C17F13

Бренд: National Instruments Страницы: 6

Бренд: Samson Страницы: 124

Бренд: Samson Страницы: 86

Бренд: VAC Страницы: 5

Бренд: Yamaha Страницы: 5

Бренд: Parker Страницы: 478

Бренд: ZPA Pecky, a.s. Страницы: 36

Бренд: AC Tech Страницы: 2

Бренд: V-TAC Страницы: 2

Бренд: Velleman Страницы: 22

Бренд: National Instruments Страницы: 27

Бренд: VALPES Страницы: 28

Бренд: GEM Страницы: 2

Бренд: VAL Страницы: 10

Бренд: Zonet Страницы: 2

Бренд: Atmel Страницы: 150

Бренд: PACH & COMPANY Страницы: 39

Бренд: UCS Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды