Epson S1C17602 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 368

background image

3 MeMORY MaP

3-4

Seiko epson Corporation

S1C17624/604/622/602/621 TeChniCal Manual

Flash area

3.2

embedded Flash Memory

3.2.1

The S1C17624/604 contains a 128K-byte Flash memory (4K bytes

×

32 sectors), the S1C17622/602 contains a

64K-byte Flash memory (4K bytes

×

16 sectors), and the S1C17621 contains a 32K-byte Flash memory (4K bytes

×

8 sectors) for storing application programs and data.

2.1.1 Embedded Flash Memory

Table 3.

S1C17624/604

S1C17622/602

S1C17621

Flash memory capacity

128K bytes

64K bytes

32K bytes

Address range

0x8000 to 0x27fff

0x8000 to 0x17fff

0x8000 to 0xffff

Address 0x8000 is defined as the vector table base address, therefore a vector table (see “Vector Table” in the “In-
terrupt Controller (ITC)” chapter) must be placed from the beginning of the Flash memory. The vector table base
address can be modified with the MISC_TTBRL/MISC_TTBRH registers.
The Flash memory can be read in 1 to 5 cycles.

Flash Programming

3.2.2

The S1C17624/604/622/602/621 supports on-board programming of the Flash memory, it makes it possible
to program the Flash memory with the application programs/data by using the debugger through an ICDmini
(S5U1C17001H). Furthermore, the S1C17624/604/622/602/621 supports self-programming by the application pro-
gram. The Flash memory can be programmed in 16-bit units. The Flash memory supports two erase methods, chip
erase and sector erase.For the Flash programming using the debugger, see the “S5U1C17001C Manual” included
in the S1C17 Family C Compiler Package. For the self-programming controlled by the user program, see the “Self-
Programming (FLS) Application Notes” for the S1C17624/604/622/602/621.

note: The debugger supports chip erase only and does not allow erasing in sector units.

Protect Bits

3.2.3

In order to protect the memory contents, the Flash memory provides two protection features, write protection and
data read protection, that can be configured for every 16K-byte areas. The write protection disables writing data to
the configured area. The data-read protection disables reading data from the configured area (the read value is al-
ways 0x0000). However, it does not disable the instruction fetch operation by the CPU.
The Flash memory provides the protect bits listed below. Program the protect bit corresponding to the area to be
protected to 0.

Flash Protect Bits (S1C17624/604)

address

Bit

Function

Setting

init. R/W

Remarks

0x27ffc

(16 bits)

D15–8 reserved

–

–

–

D7

Flash write-protect bit for 0x24000–0x27fff

1 Writable

0 Protected

1 R/W

D6

Flash write-protect bit for 0x20000–0x23fff

1 Writable

0 Protected

1 R/W

D5

Flash write-protect bit for 0x1c000–0x1ffff

1 Writable

0 Protected

1 R/W

D4

Flash write-protect bit for 0x18000–0x1bfff

1 Writable

0 Protected

1 R/W

D3

Flash write-protect bit for 0x14000–0x17fff

1 Writable

0 Protected

1 R/W

D2

Flash write-protect bit for 0x10000–0x13fff

1 Writable

0 Protected

1 R/W

D1

Flash write-protect bit for 0xc000–0xffff

1 Writable

0 Protected

1 R/W

D0

Flash write-protect bit for 0x8000–0xbfff

1 Writable

0 Protected

1 R/W

address

Bit

Function

Setting

init. R/W

Remarks

0x27ffe

(16 bits)

D15–8 reserved

–

–

–

D7

Flash data-read-protect bit for 0x24000–0x27fff 1 Readable

0 Protected

1 R/W

D6

Flash data-read-protect bit for 0x20000–0x23fff 1 Readable

0 Protected

1 R/W

D5

Flash data-read-protect bit for 0x1c000–0x1ffff

1 Readable

0 Protected

1 R/W

D4

Flash data-read-protect bit for 0x18000–0x1bfff 1 Readable

0 Protected

1 R/W

D3

Flash data-read-protect bit for 0x14000–0x17fff 1 Readable

0 Protected

1 R/W

D2

Flash data-read-protect bit for 0x10000–0x13fff 1 Readable

0 Protected

1 R/W

D1

Flash data-read-protect bit for 0xc000–0xffff

1 Readable

0 Protected

1 R/W

D0

reserved

1

1 R/W Always set to 1.

«
...
40
41
42
43
44
...
»

Содержание S1C17602

















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S1C17602

Бренд: Samsung Страницы: 27

Бренд: Procom Страницы: 10

GAT Access 6600 Series

Бренд: Gantner Страницы: 4

Бренд: Uniteck Страницы: 46

Tacosol Load EXA L

Бренд: Taconova Страницы: 40

Бренд: t.a.c. Страницы: 6

Бренд: Zareba Страницы: 40

COMPASS SC-RS 232

Бренд: BFT Страницы: 24

Бренд: M-system Страницы: 8

Бренд: S&S Northern Страницы: 8

Бренд: digitalview Страницы: 18

Бренд: Nitrous Express Страницы: 20

Бренд: SAES Страницы: 36

Бренд: Instruments of Things Страницы: 12

Бренд: Wahlberg Страницы: 40

Бренд: Trio Страницы: 8

Бренд: YGE Страницы: 2

M-SYSTEM DANAGE

Бренд: SENTRONIC Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды