manualshive.com logo in svg

Epson RX595 - Stylus Photo Color Inkjet, Руководство по обслуживанию, Страница: 49 / 131

Поделиться
Скачать
Epson RX595 - Stylus Photo Color Inkjet Скачать руководство пользователя страница 49

EPSON Stylus Photo RX585/RX595/RX610

Revision B

Troubleshooting

Troubleshooting When There is Error Display

49

Maintenance 
error

A0H

Waste ink overflow

Life expiration of maintenance 
parts

†

Replace all the maintenance parts, and clear the maintenance counter.

♦

 

Refer to “6.1.1 Maintenance Error” 

(p.116)

Abnormal 
operation

88H

Inserted tray error during cleaning

An error occurred during 
cleaning

†

Pulling out the CDR Tray

†

Checking the CDR Tray Sensor 

(p.90)

♦

Checking the CDR Tray Sensor for adhesion of dirt or dust

♦

Checking the connection of the connector of the CDR Tray Sensor

†

Checking the connection of the FFC

†

Checking the following parts and replace the defective one:

♦

CDR Tray Sensor 

(p.93)

♦

CDR Tray

89H

Overhit detection error during cleaning

†

Checking the operation of the Carriage Assy;
Move the Carriage Assy by hand, and check to see if it moves smoothly.

†

Checking the following parts and replacing the defective one:

♦

Checking the lead wires of the CR Motor (CN14) for disconnection or breakage

♦

Checking the CR Encoder FFC (CN1) for disconnection or breakage

♦

Checking the printer frame for adhesion of dirt or insufficient lubrication 

(p.119)

♦

Checking the CR Guide Shaft for adhesion of dirt or insufficient lubrication 

(p.119)

♦

Checking the Linear Scale for adhesion of dirt or damage 

(p.75)

♦

Checking the CR Encoder for adhesion of dirt or damage 

(p.90)

♦

Checking the CR Belt for damage or improper tension 

(p.88)

♦

Checking the CR Motor and replacing it if necessary 

(p.88)

♦

Main Board 

(p.66)

Table 3-3.  Fatal Errors  (continued)

Category

Error Code

Error

Cause

Remedy

Содержание RX595 - Stylus Photo Color Inkjet




































































































































Отзывы:

Нет отзывов