background image

Epson PowerLite 737c Projector

22

 -

 Epson PowerLite 737c Projector

2/05

3. If you need to replace the filter, slide it off as shown.

4. Slide the new air filter until it clicks in place.

Replacing the Lamp 

The projection lamp typically lasts for about 2000 hours of use 
(in High Brightness mode) or 3000 hours (in Low Brightness 
mode). It is time to replace the lamp when: 

The projected image gets darker or starts to deteriorate.

The 

 lamp light is flashing orange. 

The message 

Replace the Lamp 

appears on the screen when 

the lamp comes on. To maintain brightness and image 
quality, replace the lamp as soon as possible.

Note:

You can check how many hours the lamp has been used in the Info 
menu.

Note:

Turn the projector off when not in use. Continuous use may reduce 
the overall life of the product.

Contact your dealer or call Epson at (800) 873-7766 in the 
United States for a replacement lamp. Request part number 

V13H010L32

. In Canada, please call (800) 463-7766 to locate a 

dealer. 

Follow these steps to replace the lamp:

1. Press the 

P

 

Power

 button twice to turn off the projector. 

When the 

P

 

Power

 light stops flashing, unplug the power 

cord.

2. If the projector has been on, allow it to cool down for at least 

an hour (or until the lamp is cool). 

Warning:

Let the lamp cool before replacing it. If the lamp breaks, handle 
the shards carefully to avoid injury.

3. Turn the projector over. Press in on the tabs and lift up the 

lamp cover.

4. Loosen the two screws holding the lamp in place (you don’t 

need to remove them).

5. Hold the lamp as shown and pull it straight out.

6. Gently insert the new lamp. (If it doesn’t fit easily, make sure 

it is facing the right way.)

Warning:

This product includes a lamp component that contains mercury 
(Hg). Please consult your state and local regulations regarding 
disposal or recycling. Do not put it in the trash.

Caution:

Do not touch the glass portion of the lamp assembly. Touching 
the glass could result in premature lamp failure.

7. Once the lamp is fully inserted, tighten its screws.

Содержание PowerLite 737c
























Отзывы: