Epson PERFECTION V10 Скачать руководство пользователя | Manualshive

Страница: 38 / 77

background image

EPSON Perfection V10/V100 Photo/V200 Photo/V350 Photo

Revision B

DISASSEMBLY/ASSEMBLY

Disassembly of Main Unit

38

5. Disconnect CN1, CN2, CN4, CN7 connectors, and CN5 for the V350 Photo, and

CN8 for the Perfection V100 Photo/V200 Photo to remove the Main Board.

Figure 4-12. Removing the Main Board (Perfection V100 Photo/V200 Photo/V350 Photo)

Figure 4-13. Removing the Main Board (Perfection V10)

When reassembling the Upper Main Board Shield Plate, match
the guide pin and the positioning hole, and insert the plate
under the Lower Main Board Shield Plate.

For the Perfection V100 Photo/V200 Photo/V350 Photo, make
sure to screw the Upper Main Board Shield Plate together with
the earth cable of the Harness TPU/Harness AFL.

When reassembling the Upper Main Board Shield Plate, be
careful not to get the CR Motor cable caught under the plate.

Figure 4-11. Reassembling the Upper Main Board Shield Plate

Guide pin and

positioning hole

C.B.P. 3x8

Upper Main Board Shield Plate

Insert position

C H E C K

P O I N T

Perfection V10 is equipped with a different Main Board to
Perfection V100 Photo/V350 Photo, therefore note that the number
of connectors differ.

CN1

CN2

CN4

CN7

CN5

CN8

CN4

CN7

CN1

CN2

«
...
36
37
38
39
40
...
»

Содержание PERFECTION V10














































































Отзывы:

Нет отзывов

Похожие инструкции для PERFECTION V10

IMAGECLASS MF4150

Бренд: Canon Страницы: 76

Бренд: Canon Страницы: 124

imageFORMULA DR-M160

Бренд: Canon Страницы: 56

Бренд: Canon Страницы: 2

2050C - DR - Document Scanner

Бренд: Canon Страницы: 2

Microfilm Scanner 350II

Бренд: Canon Страницы: 62

imageFORMULA ScanFront 300

Бренд: Canon Страницы: 28

imageFORMULA DR-G2140

Бренд: Canon Страницы: 182

VersaMax GFK-2721A

Бренд: GE Страницы: 62

Бренд: SICK Страницы: 18

Бренд: Microtek Страницы: 8

Contex SD4400 Series

Бренд: BERTL Страницы: 29

Бренд: CEN-TECH Страницы: 45

Smart Scanner ET16 Plus

Бренд: Renkforce Страницы: 8

Бренд: Renkforce Страницы: 29

BARSCREENSENSOR

Бренд: Goldanalytix Страницы: 16

Бренд: Halo Страницы: 32

SmartOffice PS386

Бренд: Plustek Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды