Epson Perfection 3200 Photo Скачать руководство пользователя страница 42

Страница: 42 / 78

EPSON Perfection 3200 Photo

Revision A

Disassembly and Assembly

DISASSEMBLY AND ASSEMBLY

4.2.3 Upper Cover Removal

Release the carriage lock. (See Section 4.2.1.)

Remove the document cover. (See Section 4.2.2.)

Remove the two screws (CBP, M3x8) at the back of the scanner. (See
Figure 4-6.)

While lifting up the upper cover and pulling it forward, disengage the three
hooks at the front of the upper cover, and then remove the upper cover.

Disconnect the connector (CN1) from the SUB_A circuit board. (See Figure
4-8)

Figure 4-6. Upper Cover Removal (1) - Screw Positions

Figure 4-7. Document Cover Removal (2)

Figure 4-8. Upper Cover Removal (3)

C A U T I O N

When removing the upper cover, make sure that the hooks
are properly disengaged so that the tabs do not get broken.

CBP Screws (3x8)

Tightening Torque : 8-10kgfcm

Hooks

Connector

Содержание Perfection 3200 Photo















































































Результаты поиска

Содержание Perfection 3200 Photo

Отзывы:

Похожие инструкции для Perfection 3200 Photo

Бренды по названию

Популярные бренды

Epson Perfection 3200 Photo, Руководство по обслуживанию

Результаты поиска

Содержание Perfection 3200 Photo

Отзывы:

Похожие инструкции для Perfection 3200 Photo

Бренды по названию

Популярные бренды