Epson Perfection 1200PHOTO Скачать руководство пользователя страница 55

Страница: 55 / 94

EPSON Perfection1200

Revision B

Firmware Update

5.1 Firmware Update

Firmware update is required after replacing the Main Board. The following
items are necessary for the update:

Update Program Disk (P10B01W)

SCSI or USB Cable (“S” or “U” depending on the model type)

5.1.1 Operating Environment for the
Update Program

Supported OS:

Windows98 exclusive

Operating Condition:

TWAIN Driver (enclosed with the scanner) must
have been installed.

5.1.2 Installation of the Update Program

Install the Firmware Update Program according to the following steps:

Double-click the set-up file

“P10B01W.exe”

in the Update Program disk,

and the following screen will appear.

Figure 5-1. Setting up P10B01W (1)

Confirm the installation folder and click

, and the program will be

automatically installed.

5.1.3 Updating Method

Connect the scanner to the PC using SCSI or USB cable, and turn on the
scanner. Confirm that the status lamp (green) is on, or lift up the document
cover to confirm the fluorescent lamp (white) is on.

Select

Start, Program

Program for Production

, and

P10B01W

execute the program.

When a screen shown in Figure 5-2 appears, select one of the products
you wish to update by clicking the product name or using the cursor keys.

Click

Next

or press

Enter

Figure 5-2. P10B01W (2)

Содержание Perfection 1200PHOTO































































































Результаты поиска

Содержание Perfection 1200PHOTO

Отзывы:

Бренды по названию

Популярные бренды

Epson Perfection 1200PHOTO, Руководство по обслуживанию

Результаты поиска

Содержание Perfection 1200PHOTO

Отзывы:

Бренды по названию

Популярные бренды